The Hobby eStore

Mini Moto 50cc - Moviestar Colours

Tue, 16 Mar 2010 15:17:28 +0000

]]>

UK DELIVERY ONLY.

These bikes have been made and designed with the enthusiast in mind to replicate the real thing. These bikes are probably not the cheapest thing on the market, but a lot cheaper than the real thing! Top speed is dependant upon the rider (Maximum weight is roughly 85Kg or 13stone) but the average is 30-35 MPH and a just inchs off the ground it feels 10 times as fast!

Description

Max. speed: 35 kph
Range/tank: 35 - 45 miles
Max. load: 300lbs
Engine: 47cc, single cylinder, 2-stroke, air-cooled
Fuel: 25:1 gasoline / engine oil mix
Fuel tank: 1.7L
Start method: manual start
Ignition: CDI
Wheels: 10" (tubeless tires)
Brakes: front and rear disc brakes
Material:
- Frame: steel
- Cover: ABS plastic

TERMS of Sale for Mini Motos:

All motorbikes and quad-bikes, are dangerous. Please wear safety equipment at all times when using bikes or similar machines. The use of any powered vehicle could involve the risk of injury or death. Please use these products in a responsible manner.

The products that we supply are technical & mechanical products, which require mechanical knowledge and skill to use and maintain. You should not purchase a Mini Moto unless you have a good understanding of how to use and maintain them.

None of the bikes we provide are 'road legal' and are not for use on the public highway. These bikes are intended to be enjoyed on private property. Use of these bikes on a public highway could result in criminal proceedings.

The Following parts are not covered by any warranty offered on Mini Moto's:

Chains & Belts;
Fairings/ bodywork (24 hours after delivery Photos required)
Pull Starts or Inner Cogs;
Clutches or springs
Brake Callipers;
Exhaust Pipes;
Tyres, Wheels, valves and Inner Tubes;
Spark Plugs;

Any other parts of a similar wear and tear nature to those listed above and any part that has been damaged as a result of accident damage or lack of maintenance.

If within any warranty period your machine develops a fault, you must contact us and we will advise how to best rectify the problem and dispatch parts, without charge, during the first 14 days, providing the parts required are under warranty. Please note customers will be expected to fit parts themselves, guidance will be available on technical issues.

]]>

Mini Moto 50cc - Camel Racing Colours

Tue, 16 Mar 2010 15:13:19 +0000

]]>

UK DELIVERY ONLY.

Description

Max. speed: 35 kph
Range/tank: 35 - 45 miles
Max. load: 300lbs
Engine: 47cc, single cylinder, 2-stroke, air-cooled
Fuel: 25:1 gasoline / engine oil mix
Fuel tank: 1.7L
Start method: manual start
Ignition: CDI
Wheels: 10" (tubeless tires)
Brakes: front and rear disc brakes
Material:
- Frame: steel
- Cover: ABS plastic

TERMS of Sale for Mini Motos:

Any other parts of a similar wear and tear nature to those listed above and any part that has been damaged as a result of accident damage or lack of maintenance.

]]>

Mini Moto 50cc - Fila Racing Colours

Tue, 16 Mar 2010 15:12:04 +0000

]]>

UK DELIVERY ONLY.

Description

Max. speed: 35 kph
Range/tank: 35 - 45 miles
Max. load: 300lbs
Engine: 47cc, single cylinder, 2-stroke, air-cooled
Fuel: 25:1 gasoline / engine oil mix
Fuel tank: 1.7L
Start method: manual start
Ignition: CDI
Wheels: 10" (tubeless tires)
Brakes: front and rear disc brakes
Material:

Frame: steel
Cover: ABS plastic

TERMS of Sale for Mini Motos:

Any other parts of a similar wear and tear nature to those listed above and any part that has been damaged as a result of accident damage or lack of maintenance.

]]>

A-10 Thunderbolt II 4-CH RC Brushless Scale Model Jet Aeroplane

Wed, 24 Feb 2010 17:21:39 +0000

]]>

The A-10 Thunderbolt II (also known as the Warthog) is an American single-seat, twin-engine, straight-wing jet aircraft designed to provide close air support of ground forces. It was the first USAF aircraft designed exclusively for close air support.

The A-10 has superb manoeuverability even at low speeds and altitude, this is due to its large wing area, high wing aspect ratio, and large ailerons. This design also enables short takeoffs and landings, allowing it top operate from the smallest and most basic airfields.

This model replica of the A-10 Thunderbolt II is 90% assembled, so you can get it in the air within minutes of opening the box. When it is airbourne it has full four channel radio control, allowing adjustment of the aileron, elevator, throttle, and when the plane is on the ground, it is complete with front wheel steering!

Powered by twin gutsy 2410-size brushless motors(1200KV) this plane is capable of high speed, 3D aerobatic stunts and also is able to fly in blustery conditions. The A-10 is a confident acrobat and capable of a full range of impressive tricks and manoeuvres in experienced hands. It can perform: inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins.

Despite its aerobatic pedigree, the same design that gives it the ability to carryout breathtaking 3D moves, means it is a stable plane and so also suitable for the beginner and mid-level pilot too.

The Thunderbolt has a powerful brushless motor, and a 2.4Ghz radio transmitter, making it a perfect choice for the enthuiast. We have also upgraded the charger from a standard one, to a balanced charger included in the price. This makes charging safer and better for the battery.

Specs
Wing span: 872mm
Length: 968mm
Flying Weight: 450g
Drive: Twin brushless motors 1200KV
Speed Controller: 25A brushless ESC
Servo: 3x10g
Battery: 11.1V 15C 1500MAH Li-Po
Charger: Li-Po balance charger
Control: 4 CH Radio Tx and Rx
Range: 1000 feet

Features
4 CH Full RC - Aileron, Elevator, Wheel, Throttle
Full aerobatic characteristics
Powerful brushless motors
Excellent stability
Ready to Fly in Just Minutes!
Super tough & Lightweight
Shock Resistant Fuselage
Pre-installed Electronics
Suitable for beginners and experts
Only required 8 AA batteries for the transmitter to start flying
10-15 minutes flight time

]]>

4 CH Catalina RC 2.4G Brushless Electric Twin Power Sea Plane

Wed, 24 Feb 2010 17:15:16 +0000

]]>

The Catalina was an American flying boat of the 1930s and 1940s, produced by Consolidated Aircraft. It was such a versatile aeroplane that it performed numerous functions during WWII, and was used by the Air Forces, Armies and Navies of many countries.

Catalinas were used in anti-submarine warfare, patrol bombing, convoy escorts, search and rescue missions and cargo transport. It was the most successful aircraft of its kind and produced in greater numbers than any other flying boat. Some remained in military service until the 1980s and even today the Catalina continues to be used as an airtanker in some parts of the world.

The Catalina has full four channel radio control allowing adjustment of the aileron, elevator, rudder, and throttle; it can even be steered when floating on the water. Yes, water! This model sea plane has been designed so that it can actually take off and land on water, the twin brushless motors it is powered with can send it soaring effortlessly from your local lake or pond, into the sky. It really does look spectacular, see the video below!

The design of this aeroplane does not make it as agile as some other models, but it can pull a loop from a shallow dive and looks fantastic doing a low flypast either over land or water. In any case the power of the twin brushless motors enables it to be flown in many conditions, even when it is windy.

The Catalina is nearly ready to fly straight from the box, all the necessary glue and tools are included in the in the carton and you will have it flying in no more than a few minutes. All you'll need are 8 AA batteries for the transmitter.

The Catalina has a powerful brushless motor, and a 2.4Ghz radio transmitter, making it a perfect choice for the enthuiast. We have also upgraded the charger from a standard one, to a balanced charger included in the price. This makes charging safer and better for the battery.

Specs
Wing span: 1380mm
Length: 880mm
Flying Weight: 780g
Battery: Li-po 11.1V-1500mAh
Power: twin C2410 brushless motors
Control : 4CH RC system, 4 servos
2 x 25A brushless ESC
Range: 1000 feet

Features
4 CH Full RC - Aileron, Elevator, Rudder, Throttle
Rudder can steer on ground and water
Powerful brushless motor
Excellent stability
Ready to Fly in Just Minutes!
Super tough
lightweight
Shock Resistant Fuselage
Strong Wings
Pre-installed Electronics
Suitable for beginners and experts
Only required 8 AA batteries for the transmitter to start flying

]]>

Messerschmitt T-109 4 CH Radio Control RC Scale Brushed Fighter

Wed, 24 Feb 2010 17:10:37 +0000

]]>

The T-109, otherwise known as the Messerschmitt Bf 109Z, is a heavy fighter which was designed by joining two Bf 109 (Me-109) fighters together. The T-109 was the result, on paper at least it was a single seater with the pilot sitting in the left fuselage. The T-109 would have been heavily armed with five 30 mm cannons.

Four versions of this plane were planned, but only one prototype was ever built in 1942-43. Eventually the project was cancelled due to the arrival of the Messerschmitt Me 262, which was expected to perfom better. So here is your chance to fly the fighter plane that never was!

Like many of our planes this model is virtually ready to fly straight from the box, all you'll need is 8 AA batteries to power the transmitter. We have specified this plane with the 35Hz controller and brushed motor options, making it an affordable entry level outfit, ideal for someone wanting to buy their first plane.

This model is lightweight, extremely tough, with a reinforced fuselage and wings, so it's as crash resistant as possible. The fuselage has been factory finished, and the details of original design have been carefully reproduced.. This plane features excellent stability and amazing aerobatic capabilities. Once you've become experienced, you will have it performing inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and even spins!.

Specs
Wing span: 1200mm
Length: 780mm
Flying Weight: 410g
Power: twin 370 carbon brush motor
Gearbox: 1:5.33 gear w 1080 propeller
Speed Controller: 40A ESC
Servo: 3x10g
Battery: 9.6V 650mAh Ni-MH
Control: 4 CH Multifunctional Radio Tx/Rx Range: 500 feet

Features
4 CH Full RC - Aileron, Elevator, Rudder, Throttle
Full aerobatic characteristics
Powerful brushed motor
Excellent stability
Ready to Fly in Just Minutes!
Super tough
lightweight
Shock Resistant Fuselage
Strong Wings
Pre-installed Electronics
Suitable for beginners and experts
Only required 8 AA batteries for the transmitter to start flying

]]>

Messerschmitt ME-109 (Bf-109) 4 CH RC Scale 2.4G Brushless Plane

Wed, 24 Feb 2010 17:00:34 +0000

]]>

The Messerschmitt Bf 109 (often nicknamed the Me-109) was a German World War II fighter aircraft designed by Willy Messerschmitt in the early 1930s. It was one of the first true modern fighters of the era, including such features as an all-metal monocoque construction, a closed canopy, and retractable landing gear.

The first 109s saw service in the Spanish Civil War, and then became the mainstay fighter plane of the Luftwaffe during World War II. During the Battle of Britain the 109 was used in new roles as an escort fighter, a fighter-bomber and for photo-reconnaissance.

A polished aerobatic performer, the Me 109 was credited with more aerial kills than any other aircraft in the second World War.

As you can see from the picture above, this replica has been meticulously created, faithfully reproducing the famous warbird, in a manner that does its aeronautical reputation justice. You'll be able to do it justice too, within minutes of opening the box as it is 90% assembled for you at the factory.

This model has a really tough, but lightweight airframe, and the outer shell has been superbly finished, carefully emulating the details of the real thing. This fighter model is incredibly stable and will fly at low speed, and at low altitude making it simple, safe and fun, even for the beginner.

The Messerschmit's design makes it a brilliant 3D aerobatic performer for the experienced pilot: inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are possible; it can roll very quickly and is super stable even when flying upside down. The wing and body used in this plane are specially designed to allow high G manoeuvres, however the wing loading is still very low.

The Me-109 has a powerful brushless motor, and a 2.4Ghz radio transmitter, making it a perfect choice for the enthuiast. We have also upgraded the charger from a standard one, to a balanced charger included in the price. This makes charging safer and better for the battery.

Specs
Wing span: 900mm
Length: 780mm
Flying weight: 405g
Drive: 2410 Brushless Motor 1200KV
Speed Controller:20A Brushless ESC
Servo: 3x10g
Battery: 11.1V 1000mah 15C LiPo Battery
Control: 4 CH Radio Tx & Rx
Range: 1000 feet

Features
4 CH Full RC - Aileron, Elevator, Rudder, Throttle
Rudder helps steer plane on ground
Full aerobatic characteristics
Powerful brushless motor
Excellent stability
Ready to Fly in Just Minutes!
Super tough
lightweight
Shock Resistant Fuselage
Strong Wings
Pre-installed Electronics
Suitable for beginners and experts
Only required 8 AA batteries for the transmitter to start flying

]]>

4 CH 2.4G Tiger Moth Radio Control Brushless Biplane

Wed, 24 Feb 2010 16:54:00 +0000

]]>

The de Havilland DH 82 Tiger Moth is a 1930s biplane designed by Geoffrey de Havilland and was operated by the Royal Air Force and others as a primary trainer. Over 4000 Tiger Moths were made for the RAF during World War II, and the plane remained in service until 1952. Tiger Moths are still used recreationally today.

This replica of the classic aircraft is virtually ready to fly straight out of the box, only a few minutes of tinkering will be required to get this compact, and quiet aeroplane in the air.

This model has a really tough, but lightweight airframe, and the outer shell has been superbly finished, carefully emulating the details of the real thing. The Tiger Moth is incredibly stable and will fly at remarkably low speeds, and at low altitude making it simple, safe and fun, even for the beginner.

The Tiger Moth's design also makes it an excellent 3D aerobatic performer for the experienced pilot: inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are possible; it can roll very quickly and is super stable even when flying upside down.

This model has a powerful brushless motor, and a 2.4Ghz radio transmitter, making it a perfect choice for the enthuiast. We have also upgraded the charger from a standard one, to a balanced charger included in the price. This makes charging safer and better for the battery.

Specs
Wing span: 800mm
Length: 670mm
Flying weight: 400g
Battery: Li-Po 11.1V-1000mAh
Power: C2410 brushless motor
Control: 4CH RC system
4 servos
25A brushless ESC
Range: 1000 feet

Features
4 CH Full RC - Aileron, Elevator, Rudder, Throttle
Full aerobatic characteristics
Powerful brushless motor
Excellent stability
Ready to Fly in Just Minutes!
Super tough
lightweight
Shock Resistant Fuselage
Strong Wings
Pre-installed Electronics
Suitable for beginners and experts
Only required 8 AA batteries for the transmitter to start flying

]]>

4 CH P51D Mustang Electric RC Brushless 2.4G WWII Aeroplane

Wed, 24 Feb 2010 16:47:37 +0000

]]>

The P-51 Mustang was a single seater fighter plane, which was designed and built for World War II in just 117 days! The Royal Air Force used it as a fighter bomber, a reconnaissance plane, and as a bomber escort on raids over Germany in 1944. It was powered by a supercharged Rolls Royce Merlin engine and was fitted with six .50 caliber (12.7 mm) M2 Browning machine guns.

Rearward visibility was a problem with WW2 fighter planes and this was solved by using a 'bubble' or 'teardrop' canopy. This new type of canopy was a development in the P-51D version, considered the definitive Mustang, and is the model we have for you here.

This model is a faithful replica of the full size P-51D Mustang, the attention to detail in the canopy and the WWII USAF decals is excellent and will not disappoint. It is almost ready to fly straight out of the box, only a few minutes of minor final assembly steps will be required to get this legend of the 20th century airbourne.

This model is well made, although lightweight, and it is built to be crash resistant, and to give a long life of fun flying. The P-51D is exceedingly stable, and will fly at low speeds, which makes it safe and fun, even for the beginner. It is also possible to fly these planes at low altitude, great for when you're learning so those crashes aren't too severe!

The Mustang's structure, and shape makes it a brilliant 3D stunt plane for the experienced pilot: inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are possible; it can roll very quickly and is surprisingly stable even when flying upside down.

**Some of the pictures here show a green version of the plane, the one which we ship is finished in black. **

The P-51D Mustang has a powerful brushless motor, and a 2.4Ghz radio transmitter, making it a perfect choice for the enthuiast. We have also upgraded the charger from a standard one, to a balanced charger included in the price. This makes charging safer and better for the battery.

Specs
Wing span: 870mm
Length: 730mm
Flying weight: 405g
Battery: Li-Po 11.1V-1000mAh
Power: C2410 brushless motor
Control: 4CH RC system
3 servos
25A brushless ESC
Range: 1000 feet

]]>

P-47 Thunderbolt 4-Ch Radio Control RC Fighter

Wed, 24 Feb 2010 16:39:26 +0000

]]>

The P-47 Thunderbolt, (aka the "Jug") was the biggest, heaviest, and most expensive fighter aircraft in history to be powered by a single engine. It was one of the main United States Army Air Forces (USAAF) fighters of World War II.

The P-47 was effective in air combat but also a very effective plane for ground attack. It had eight .50-caliber machine guns, four per wing. When fully loaded the P-47 could weigh up to eight tons.

This aircraft became popular with many air forces around the world.

Once you've opened the box, this replica P-47 will be ready for take-off in only a few minutes, everything you need to fly (apart from 8 AA batteries for the transmitter) is included in the package. We have specified this plane with the 35Hz controller and brushed motor options, making it an affordable entry level outfit, ideal for someone wanting to buy their first plane.

This model is lightweight, extremely tough, and the fuselage has been finished, carefully emulating the details of the original aeroplane. This plane features excellent stability and awesome aerobatic capabilities. An experienced pilot will have it performing inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and even spins!

Specs
Wing span: 830mm
Length: 730mm
Flying Weight: 400g
Power: 370 carbon brush motor
Speed Controller: 25A speed controller
Servo: 3x10g
Battery: 8.4 V 650mah Ni-MH
Control: 4 CH Multifunctional Radio Tx/Rx Range: 500 feet

]]>

Focke-Wulf FW-190 4 CH Radio Control RC Scale Brushed Fighter

Wed, 24 Feb 2010 16:32:32 +0000

]]>

The Focke-Wulf Fw 190 Würger was a German single-seat, single-radial engine fighter aircraft designed by Kurt Tank in the late 1930s. It was used by the Luftwaffe during the Second World War, and is up there with the Spitfire and the P-51D Mustang as one of the best fighter planes of the period.

The Fw 190 had a top speed of over 400 mph and could undertake sorties of around 500 miles. To take down its target the Focke was equipped with two 13 mm MG 131 machine guns with 475 rpg (rounds per gun), and four 20 mm MG 151/20 E cannons with 250 rpg in the wing root and 140 rpg outboard.

Once you've opened the box, this replica Fw 190 will be ready for take-off in only a few minutes, everything you need to fly (apart from 8 AA batteries for the transmitter) is included in the package. We have specified this plane with the 35Hz controller and brushed motor options, making it an affordable entry level outfit, ideal for someone wanting to buy their first plane.

Specs
Wing span: 1010mm
Length: 890mm
Flying Weight: 410g
Power: 370 carbon brush motor
Speed Controller: 25A speed controller
Servo: 3x10g
Battery: 8.4 V 600mah Ni-MH
Control: 4 CH Multifunctional Radio Tx/Rx Range: 500 feet

Features
4 CH Full RC - Aileron, Elevator, Rudder, Throttle
Full aerobatic characteristics
Powerful brush motor
Excellent stability
Ready to Fly in Just Minutes!
Super tough
lightweight
Shock Resistant Fuselage
Strong Wings
Pre-installed Electronics
Suitable for beginners and experts
Only required 8 AA batteries for the transmitter to start flying

]]>

Spitfire 4CH Radio Controlled RC Fighter Plane Brushed 35Hz

Wed, 24 Feb 2010 16:31:19 +0000

]]>

The Supermarine Spitfire is a British single-seat fighter plane used by the RAF during WW2. It is undoubtedly one of the most famous aircraft ever built. Its graceful lines combined with outstanding handling qualities to produce a "dream plane" extremely fast, and in comparison to contemporary types was second to none.

The Spitfire was produced in greater numbers than any other British war plane and was used by many of Britain's Allies. It has an elliptical wing cross section, which allowed it to fly at higher speeds than the Hurricane and other fighters of the time, which had a more traditional wing shape.

Once you've opened the box, this replica Spitfire will be ready to grace the skies in only a few minutes, everything you need to fly (apart from 8 AA batteries for the transmitter) is included in the package.

This Spitfire is lightweight, extremely tough, and the fuselage has been finished, carefully emulating the details of the original aeroplane. This plane features excellent stability and awesome aerobatic capabilities. An experienced pilot will have it performing inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and even spins are possible!

Specs
Wing span: 870mm
Length: 720mm
Flying weight: 390g (14 oz)
Power: 370 carbon brush motor
Speed Controller: 25A speed controller
Servo: 3x10g
Battery: 8.4 V 600mah Ni-MH
Control: 4 CH Multifunctional Radio Tx/Rx Range: 1000 feet

]]>

F-14 Tomcat Jolly Rogers 6 Ch 2.4GHz RC EDF Twin 60mm Top Gun

Wed, 24 Feb 2010 16:18:03 +0000

]]>

The Grumman F-14 Tomcat is a supersonic, twin-engine, two-seat, variable-sweep winged aircraft. It was the United States Navy's primary maritime air superiority fighter, fleet defense interceptor and tactical reconnaissance platform from 1974 to 2006. In 1986, the F-14 was the main aircraft featured in the Tom Cruise film Top Gun, spawning a surge in U.S. Navy recruiting.

The F-14 Tomcat was designed as both an air superiority fighter and a long-range naval interceptor, it has a two seat cockpit with a canopy that gives all-round visibility. The Tomcat's defining feature is its variable geometry wings that swing automatically during flight; for high-speed intercept, they are swept back, and they then swing forward again for lower speed flight. It has a maximum speed of Mach 2.34 (1,544 mph) at high altitude, and has a service ceiling of 50,000 ft.

This incredible jet aircraft is equipped with an internal 20 mm M61 Vulcan Gatling-type gun mounted on the left side, and can carry AIM-54 Phoenix, AIM-7 Sparrow, and AIM-9 Sidewinder anti-aircraft missiles.

Now for the details on the F-14 Jolly Rogers which you can fly! Like all the planes in the Starmax range, the F-14 is finished in the factory to a high standard and represents an excellent replica of the real aircraft. But this one is special, not only does it look like the real McCoy but it shares most of the functionality of the real thing too. The variable geometry or swing-wings on this model jet actually work, as does the landing gear, thanks to its 6 channel electronics. You can control each position of the wings from fully open to fully retracted. How good does this jet look with the wings fully retracted?!

The F-14 Jolly Rogers is an extremely high spec model; it features twin 60mm EDF jets, twin ESCs and a massive 3200mAh battery, making it very quick.

This model is an amazing 3D aerobatic aircraft, and capable of incredible speed. The twin engined punch that this plane packs allows it to perform a full aerobatic display: inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are all possible. If you're really good you will be able to perform the famous 'Cobra Manoeuvre' with this Tomcat.

This plane is 90% assembled and so only a few minutes of final finishes are needed before you can fly. Also everything you need is in the box, apart from 8 AA batteries, which you'll need to power the radio contol transmitter.

This jet comes with a 2.4G radio which means the range is longer and more stable plus you do not have to worry about interference from other fliers. It is also equipped with a powerful brushless motor, for the best performance. The plane is made from strong but lightweight foam that is more resistant to crashes and gives easier stable flight even in windy conditions. This aeroplane can take off from the ground or can be hand launched.

Specs
Wingspan: 1100mm
Length: 1086mm
Flying Weight: 1100-1300g
Radio System:2.4G 6Ch Tx and 6 Ch Rx
Twin 60mm ducted fan
Twin motor: Powerful 2430 outer runner brushless motor
Twin ESC: 45A ESC 5A UBEC
With variable sweep wing, retract system
Battery: 3200Mah, 11.1V.Li-Po

Features
Pre-painted foam fuselage & wings
90% assembled
Pre-installed electrics
CAD engineering quality
Working swing wings
Retractable landing gear
Stunning paintwork
Twin 60mm electric ducted fans
State of the art components
2.4G Transmitter
Can perform amazing aerobatics
Powerful batteries
Approx 15min flight time
Range: 1000m

]]>

A-10 Warthog Desert Camo 5 Ch 2.4GHz RC EDF Twin Jet 64mm

Wed, 24 Feb 2010 16:10:48 +0000

]]>

The A-10 has superb manoeuverability even at low speeds and altitude, this is due to its large wing area, high wing aspect ratio, and large ailerons. This design also enables short takeoffs and landings, allowing it to operate from the smallest and most basic airfields.

Like all the planes in the Starmax range, the A-10 is finished in the factory to a high standard and represents an excellent replica of the real aircraft. Extra features like the realistic landing gear, and the clear cockpit complete with pilot add to the authenticity and realism present in this model.

This model features twin 64mm EDF jets, twin ESCs and a massive 2500mAh battery. It also has 5 channels which allows an electric landing gear retracting mechanism.

However, not only does it look fantastic, it is an amazing 3D aerobatic aircraft, and capable of incredible speed. The twin engined punch that this plane packs allows it to perform a full aerobatic display: inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are all possible.

Specs
Wingspan: 1030mm
Length: 949mm
Twin 64mm EDF, twin ESC, twin Motor
Radio System: 5Ch Tx and 6 Ch Rx
8 servos
Brushless motor and 25A ESC
Suspension electric retract system
Battery: 2500 mAh,11.1V

Features
Pre-painted foam fuselage & wings
90% assembled
Pre-installed electrics
CAD engineering quality
Retractable landing gear
Stunning paintwork
Twin 64mm electric ducted fans
State of the art components
2.4G Transmitter
Can perform amazing aerobatics
Powerful batteries
Approx 15min flight time
Range: 1000m

]]>

F-15 Desert Vectored Thrust 5Ch 2.4GHz RC EDF 70mm Jet Plane

Wed, 24 Feb 2010 16:00:14 +0000

]]>

The McDonnell Douglas (now Boeing) F-15 Eagle is a twin-engine, all-weather tactical fighter designed to gain and maintain air superiority in aerial combat. It is considered among the most successful modern fighters with over 100 aerial combat victories. The Eagle first flew in July 1972, and entered service in 1976. The F-15 is expected to be in service with the U.S. Air Force until 2025.

Since the 1970s, the Eagle has also been exported to Israel, Japan, and Saudi Arabia. Despite originally being envisaged as a pure air superiority aircraft, the design proved flexible enough that an all-weather strike derivative, the F-15E Strike Eagle, was later developed, and entered service in 1989.

This Starmax replica of the F-15 is a top-level model aeroplane, featuring vectored thrust, retractable landing gear and the craftsmanship and factory finish that people come to expect from our models.The finish and design of this foam structured plane has been undertaken to a very high standard. The fuselage is both strong and extremely light, designed to withstand the occasional crash landing. It is complete with a detailed paint job, and factory affixed decals to complete the realistic look of your F-15.

Thrust vectoring is the ability of an aircraft to direct the thrust from its engine(s) in a direction other than parallel to the vehicle's longitudinal axis. The technique was originally employed to provide upward vertical thrust as a means to give aircraft vertical (VTOL) or short (STOL) takeoff and landing ability. Soon, it was realized that using vectored thrust in combat situations enabled aircraft to perform manoeuvres not available to conventional-engined planes.

So, what does all this mean? Well, you've got a 70mm ducted fan with powerful 14.8v battery, 5ch electronics, and automatic landing gear. Coupled with the vectored thrust, this gives you one of the fastest and most agile model aeroplanes on the market for this price. You will not be disappointed!

This is an amazing 3D aerobatic aircraft, and capable of incredible speed. The punch that this plane packs allows it to perform a full aerobatic display: inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are all possible. If you're really good you will be able to perform the famous 'Cobra Manoeuvre' with this F-15.

**Some of the pictures of this model show the red version, we are shipping the desert camo paintjob - more pictures of the desert colours will be posted as soon as we have taken them**

Specs
Wingspan: 750mm
Length: 1100mm
Flying Weight: 950g
Radio: 2.4G 5Ch Tx and 6 Ch Rx
70mm Ducted fan
Motor: Powerful 2836 outer runner brushless motor
ESC: 45A ESC 5A UBEC
9 x 9g servos
1 x 17g servo, with vectored feature
Automatic landing gear system
Steering front landing gear
Battery: 4 Cell Li-Po, 2200mAh,14.8V
Charger: 4S Charger

Features
Pre-painted foam fuselage & wings
90% assembled
Pre-installed electrics
CAD engineering quality
Vectored thrust
Automatic landing gear
Stunning paintwork
70mm electric ducted fan
State of the art components
2.4G Transmitter
Can perform amazing aerobatics
Powerful batteries
Approx 15min flight time
Range: 1000m

]]>

Alpha Jet Camo Vectored Thrust 5Ch 2.4GHz RC EDF 64mm Jet

Wed, 24 Feb 2010 15:51:32 +0000

]]>

The Dassault/Dornier Alpha Jet is a light attack jet and advanced trainer aircraft, jointly manufactured by Germany and France. It is the main rival of the BAe Hawk, although it hasn't been made in as great numbers, it has been supplied to the French Air Force, Luftwaffe, Royal Thai Air Force, and the Portuguese Air Force amongst others.

Being so light and powerful makes the Alpha perfect for aerobatics and is used by the Patrouelle de France flight demonstration team to spectacular effect. The Red Bull company also own an Alpha and use it for their own demonstration purposes, painted in their own livery.

Starmax have worked their usual wonders in the finish and design of this foam structured plane. The fuselage is both strong and extremely light, designed to withstand the occasional crash landing. It is complete with a detailed paint job and looks ready for air to air combat.

The Alpha has something extra for you though: it features vectored thrust.

What all this adds up to is an exceedlingly rapid and nimble jet. In this model we have a 64mm ducted fan with powerful 14.8v battery, 5ch electronics controlling the aileron, rudder, elevator and the throttle. Coupled with the vectored thrust, this gives you one of the fastest and most agile model aeroplanes on the market for this price. This plane will travel at speeds in excess of 100mph. You will not be disappointed! The fifth channel: that's used for dropping a scale bomb!

It's not just the Patrouelle de France who can perform aerobatics in an Alpha; once you've mastered this jet you'll be able to attempt stunts such as: inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are all possible. If you're really good you will be able to perform the famous 'Cobra Manoeuvre' with your Alpha.

**Some of the pictures of this model show the blue version, we are shipping the camo version - more pictures of the correct colours will be posted as soon as we have taken them**

Specs
Wingspan: 745mm
Length: 980mm
Fly Weight: 740g
Wing Load: 56g/dm²
Radio: 2.4G ( 5Ch Tx and 6 Ch Rx)
Seven 9 gram servos
64mm Ducted fan
Brushless Powered: Powerful 2601 outer runner brushless motor
30A/45A ESC
Battery: 4 Cell Li-Po, 2200 mAh,14.8V

Features
Pre-painted foam fuselage & wings
90% assembled
Pre-installed electrics
CAD engineering quality
Retractable landing gear
Stunning paintwork
64mm electric ducted fan
State of the art components
2.4G Transmitter
Can perform amazing aerobatics
Powerful batteries
Approx 15min flight time
Range: 1000m

]]>

AMX Red Vectored Thrust 5Ch 2.4GHz RC EDF 64mm Jet Plane

Wed, 24 Feb 2010 15:37:05 +0000

]]>

The AMX International AMX "Ghibli" is a ground-attack aircraft which has been specifically designed for battlefield interdiction, close air support and reconnaissance missions. The AMX is capable of operating at high subsonic speed and low altitude, by day or night, and if necessary, from bases with poorly equipped or damaged runways.It was built in a joint venture between Brazil and Italy.

Low IR signature and reduced radar equivalent cross-section help prevent detection, while low vulnerability of structure and systems aid survivability. Integrated ECM, air-to-air missiles and nose-mounted guns provide self-defence capabilities. This combination of features enabled the Italian Air Force's AMX squadrons to fly 252 combat sorties over Kosovo as part of Operation Allied Force, without a single loss.

The AMX has something extra for you though: it features vectored thrust.

Thrust vectoring is the ability of an aircraft to direct the thrust from its engine(s) in a direction other than parallel to the vehicle's longitudinal axis. The technique was originally employed to provide upward vertical thrust as a means to give aircraft vertical (VTOL) or short (STOL) takeoff and landing ability. Soon, it was realised that using vectored thrust in combat situations enabled aircraft to perform manoeuvres not available to conventional-engined planes.

So, what does all this mean? Well, you've got a 64mm ducted fan with powerful 14.8v battery, and 5ch electronics. Coupled with the vectored thrust, this gives you one of the fastest and most agile model aeroplanes on the market for this price. This plane will travel at speeds in excess of 100mph. You will not be disappointed!

The power that this plane packs allows it to perform a full aerobatic display: inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are all possible. If you're really good you will be able to perform the famous 'Cobra Manoeuvre' with your AMX.

Specs
Wingspan: 692mm
Length: 868mm
Flying Weight: 680g
Wing area: 9dm²
Wing Load: 75g/dm²
Radio: 2.4G (4Ch Tx and 6 Ch Rx )
Four 9 gram servos
64mm Ducted fan
Brushless Powered: Powerful 2061 outer runner brushless motor
45A ESC
Battery: 4 Cell Li-Po, 2200 mAh,14.8V

Features
Pre-painted foam fuselage & wings
90% assembled
Pre-installed electrics
CAD engineering quality
Retractable landing gear
Stunning paintwork
64 mm electric ducted fan
State of the art components
2.4G Transmitter
Can perform amazing aerobatics
Powerful batteries
Approx 15min flight time
Range: 1000m

]]>

F-117 Nighthawk Stealth 5Ch 2.4GHz RC EDF 70mm Jet Plane

Wed, 24 Feb 2010 15:27:42 +0000

]]>

The Lockheed F-117 Nighthawk is a stealth ground attack aircraft formerly operated by the United States Air Force. The F-117A's first flight was in 1981, and it achieved initial operating capability status in October 1983. The F-117 was a 'black' project, an ultra-secret program for much of its life, until the late 1980s.

The F-117 is shaped to deflect radar signals and is about the size of an F-15 Eagle. The single-seat Nighthawk is powered by two non-afterburning General Electric F404 turbofan engines, and has quadruple-redundant fly-by-wire flight controls. It shares many components with the F-16 Fighting Falcon, F/A-18 Hornet and F-15E Strike Eagle.

Among the penalties for stealth are lower engine power thrust, due to losses in the inlet and outlet, a very low wing aspect ratio, and a high sweep angle (50°) needed to deflect incoming radar waves to the sides. With these design considerations and no afterburner, the F-117 is limited to subsonic speeds.

However, not only does it look fantastic, it is an amazing aerobatic aircraft, and capable of incredible speed. This model of this infamous jet fighter has got a 70mm ducted fan with powerful 14.8v battery, 5ch electronics, and automatic landing gear.The power that this plane packs allows it to perform a full aerobatic display: inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are all possible. If you're really good you will be able to perform the famous 'Cobra Manoeuvre' with this Nighthawk. The videos show you just how capable it is!

Specs
Wingspan: 734mm
Length: 1100mm
Flying Weight: 980g
Radio System: 2.4G 5Ch Tx and 6 Ch Rx
70mm Ducted fan
Motor: 2836 outer runner brushless motor
ESC: 45A ESC 5A UBEC
Seven 9g servos, one 17g servo
Automatic landing gear system
Steering front landing gear
Battery: 4 Cell Li-Po, 2200mAh,14.8V
Charger: 4S Charger

Features
Pre-painted foam fuselage & wings
90% assembled
Pre-installed electrics
CAD engineering quality
Automatic landing gear
Stunning paintwork
70mm electric ducted fan
State of the art components
2.4G Transmitter
Can perform amazing aerobatics
Powerful batteries
Approx 15min flight time
Range: 1000m

]]>

A-4 Blue Angels Skyhawk 4Ch 2.4GHz RC EDF 55mm Jet Plane

Wed, 24 Feb 2010 15:10:43 +0000

]]>

The Douglas A-4 Skyhawk is a delta winged, carrier-capable, ground-attack aircraft designed for the United States Navy and U.S. Marine Corps. Fifty years after the aircraft's first flight, and having played key roles in conflict including the Falkland's War, some of the nearly 3,000 Skyhawks produced remain in service.

The A-4 Skyhawk was used by the Blue Angels between 1974 and 1986. The Blue Angels are the US Navy's Navy Flight Demonstration Squadron; they first performed in 1946 and are currently the world's oldest flying aerobatic team. The striking blue and yellow planes are supremely capable, aerobatic performers.

Starmax have produced an excellent replica of the A-4 in these stunning Blue Angel colours. The EPO foam fuselage is both strong and extremely light, designed to withstand the occasional crash landing. The authentic decals finish off the look and you are presented with a fantastic looking model.

The A-4 has a powerful brushless motor and a 55mm fan, this is a smaller fan than our other jets, and is an ideal entry level into the world of model jet piloting. Despite its smaller fan, the Skyhawk is no slouch and this model is capable of 90mph!

The delta wing design and lightweight fuselage enable this aeroplane to be supremely manoeuverable and in the right hands will take your breath away with the 3D aerobatics it can pull off. Stunts the A-4 is capable of include: inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are all possible. If you're really good you will be able to perform the famous 'Cobra Manoeuvre' with your Alpha.

The A-4 is also available in a grey colour scheme, for those who prefer a more military look and feel to their model aircraft, whatever colour you choose, they both have the same awesome power and handling.

Specs
Wingspan: 468mm
Length: 680mm
Flying Weight:450g
Wing area: 7dm²
Wing Load: 65g/dm²
Radio System: 4Ch Tx and 6 Ch Rx
Four 9 gram servos
55mm Ducted fan
Brushless motor
30A ESC
Battery: 3 Cell Li-Po,1300 mAh,11.1V

Features
Pre-painted foam fuselage & wings
90% assembled
Pre-installed electrics
CAD engineering quality
Stunning paintwork
55 mm electric ducted fan
State of the art components
2.4G Transmitter
Can perform amazing aerobatics
Powerful batteries
Approx 15min flight time
Range: 1000m

]]>

F-5E SWISS Tiger 2.4GHz RC EDF 64mm Jet

Sat, 20 Feb 2010 00:01:00 +0000

]]>

The Northrop F-5A/B Freedom Fighter and F-5E/F Tiger II are part of a family of widely used, light supersonic fighter aircraft, designed and built by Northrop in the United States, beginning in the 1960s. Hundreds remained in service in air forces around the world, even into the early 21st Century, and the type has also been the basis for a number of other aircraft.

This particular variant was used by the Patrouille Suisse, an aerobatic team of the Swiss Air Force founded in 1964. The team currently flies six Northrop F-5E Tiger II fighter/bomber jets.

Like all the planes in the Starmax range, the F-5E is finished in the factory to a high standard and represents an excellent replica of the real aircraft. Extra features like the realistic landing gear, and the clear cockpit complete with pilot add to the authenticity and realism present in this model.

However, not only does it look fantastic, but - as you'd expect from an aeroplane selected by an International aerobatic team - it is an amazing 3D aerobatic aircraft, and capable of over 90mph. This package of power and size, gives it a fantastic repertoire in experienced hands with a tremendous roll rate and an ability to climb vertically at incredible speed. The videos show you just how capable the F-5E is! If you're really good you will be able to perform the famous 'Cobra Manoeuvre' with this jet. It is launchable by hand or will take off from the ground with ease.

Specs
Wingspan: 532mm
Length: 939mm
Flying Weight: 500g
Wing area: 7dm²
Wing Load: 70g/dm²
Radio System: 4Ch Tx and 6 Ch Rx ,
Five 9 gram servos
64MM Ducted fan
Brushless motor and 25A ESC
Battery: 1300Mah, 11.1V.

Features
Pre-painted foam fuselage & wings
90% assembled
Pre-installed electrics
CAD engineering quality
Retractable landing gear
Stunning paintwork
Capable of over 90mph
64mm electric ducted fan
State of the art components
2.4G Transmitter
Can perform amazing aerobatics
Is capable of the 'Cobra Manoeuvre'
Approx 15min flight time
Range: 1000m

]]>

Super Cub Piper PA-18 4CH RC 2.4G Brushless Plane

Fri, 19 Feb 2010 23:30:07 +0000

]]>

The Piper PA-18 Super Cub is a two-seat, single-engine monoplane, introduced in 1949 by Piper Aircraft. Over 9,000 were built in nearly 40 years of production. The Super Cub was renowned for its ability to take off and land in short distances, and due to this was made into float planes as well. The real thing would cruise at around 185 km/h, 115 mph, at altitudes up to 19,000 feet.

The new Dynam Super Cub PA-18 is ready to fly (RTF) with all electronics pre-installed. So you can have it out of the box and up in the air, within a matter of minutes.

This plane is suitable for all users, from the novice to the expert, and will keep the most experienced of pilots entertained with its aerobatic skill.
Its light-weight, strong, and crash resistant so that you can fly it with confidence no matter what your ability. This plane comes with a powerful, brushless motor system which enables it to perform 3D aerobatic stunts, and to be flown easily, even in windy conditions. You can even steer the rear wheel for greater control on the ground!

The Super Cub comes with a 2.4G radio which means the range is longer and more stable plus you do not have to worry about interference from other fliers. The plane is made from strong but lightweight foam that is more resistant to crashes and gives easier stable flight even in windy conditions. The plane can take off from the ground or can be hand launched.

Specs
Wing Span: 1070mm
Overall Length: 710mm
Fly Weight: 530g
Wing Area: 17.1dm²
Fuselage Length: 630mm
Drive System: Brushless Motor (1750kv)
Servo: 3X 9g High Speed Micro Servos
Speed Controller: 25A Brushless ESC
Battery: 11.1V 1250mAh Li-Polymer
Control: 4 CH Transmitter and 6 CH Micro Receiver
Range: 1000m

Features
Dynam Super Cub PA-18 4CH RC Remote Control Plane
Brushless Motor and ESC
4CH Transmitter/Receiver
110V-240V Power Adapter
LiPo Battery Balance Charger
11.1V 1250mAh Li-Po Rechargeable Battery
2 Propellers and Landing Gear
English User Manual

]]>

Cessna EP 400 4CH Brushless Electric RC Plane

Fri, 19 Feb 2010 23:25:22 +0000

]]>

Cessna is a brand of aeroplane manufacturer that almost everyone is familiar with, so when you fly one of our Cessna 400s, you'll be cutting a recognisable shape in the sky! More people have learned to fly for real in one of these than any other plane so it's the perfect place to start and develop your RC aeronautical skills.

Not only is this plane a great one to learn on, but the Cessna 400 is set up to perform 3D aerobatic manoeuvres too. It is not only lightweight, but strong and more importantly in those first flights, it's crash resistant! All the necessary electronics are pre-installed, so it's only a matter of minutes from opening the box, conducting the final assembly steps and you'll have this 4 channel aircraft soaring through the skies.

The Cessna EP 400 is fitted with a brushless motor, which has several advantages over the brushed type. They are more efficient and reliable, make less noise, haver a longer lifetime, and most importantly they deliver more power! Added together this gives your aeroplane better capabilities for performing 3D aerial stunts.

Specs
Length: 762mm
Wing Span: 960mm
Wing area: 15.3dm sq
Flying weight: 430g
Wing loading: 28.1g/sq dm
Motor: Brushless Motor(kv1750)
Battery: LiPo 11,1V-1250 mAh - 10C
ESC: 18A
Radio: Dynam Ne-Ko 4 channel, 35 mHz
Servo: 3 stk Dynam microservo, 8.4g
Receiver: micro receiver - 5 CH
Propeller: 2 stk Dynam 8x4,3
LiPo lader: 12V Dynam LiPo 11,1V 3s

Features
Moulded foam airframe parts
Extensive decal sheet
Pre-installed servos and pushrods
Pre-installed BP-12 brushless outrunner motor with 18 Amp brushless speed control
Propellers
Molded plastic cowl
Landing Gear

]]>

Jaguar 3 CH Military J3 Piper Cub RC Warbird Aeroplane

Fri, 19 Feb 2010 23:20:32 +0000

]]>

This Jaguar is a Piper Cub based military aeroplane, it is factory finished in its United States Air Force livery and looks like an authentic World War II, Warbird.

This is a great beginners plane and comes nearly fully assembled in the box, all you have to do is snap on a few final parts, and you're off! No tools are required.

Its two-stick three channel transmitter allows you to simply control up, down, left and right, so even a novice should have it flying in minutes. This plane has been configured with brushed motor/35Hz combination making it an ideal, low cost, entry level option for someone wanting to sample the world of radio controlled aeroplanes for the first time.

Specs
Wing span: 955mm
Length: 730mm
Weight: 640g
Battery: 8.4v-650mAh NI-MH
Power: 380 brushed motor
4channel TX and RX
2*9g servo,
1*25A brush ESC
Flying weight:450g

Features
Flying time: approx. 15 mins
Flying height: approx. 300m
Range: 500m
Millitary USAF Livery
Can take off from the ground or hand

]]>

Extra 330 4ch 2.4g Brushless aerobatic plane

Fri, 19 Feb 2010 21:16:48 +0000

]]>

Fly in 3D and perform aerobatic manoeuvres with the new Dynam Extra 330. This 4 channel plane has been designed specifically with acrobatic flight in mind to make pulling off stunts and tricks much easier. Its almost ready to fly with everything included and will only take minutes to complete the minor assembly needed. This plane is designed with meticulous care and will not disappoint. It even comes with an aeroplane pilot inside the cockpit!

To perform some aerobatic stunts a lot of power is required but that is no problem for the Extra 330 as it is fitted with a brushless motor and ESC. The combination of this along with the high capacity li-polymer rechargeable battery gives the plane tonnes of power for true 3D flight.

The Extra 330 comes with a 2.4G radio which means the range is longer and more stable plus you do not have to worry about interference from other fliers. The plane is made from strong but lightweight foam that is more resistant to crashes and gives easier stable flight even in windy conditions. The plane can take off from the ground or can be hand launched.

Specs
Wing Span: 37in/940mm
Length: 29.7in/755mm
Weight: 18oz/510g
Wing Area: 14.6dm²
Motor: Brushless (1050kv)
Servos: 4 x 9g High Speed
ESC: 25A Brushless
Battery: 11.1V 1250mAh Li-Polymer
Transmitter: 4CH 2.4Ghz
Receiver: 5CH Micro
Range: 1000m

Features
4 Channel 2.4G radio
Acrobatic 3D flying
Speed 400 Brushless Motor
4 Servos
Almost ready to fly. Minor assembly required.
Everything included apart from 8 x AA batteries for the transmitter
Great Aerobatic Capabilities
Powerful li-po battery with charger
Long 20 minutes flight time

]]>

Focus EP 400 4channel 3D aerobatic RC plane

Fri, 19 Feb 2010 21:09:49 +0000

]]>

The new four channel, ready to fly Dynam Focus EP 400 is a beautifully designed single engined plane; factory finished so that you can have it out of the box and flying in minutes. Virtually ready to go, all you need to fly it are batteries and a few simple final assemply steps.

Perfect for all levels, this plane has the power and agility to perform incredible 3D aerobatic manoeuvres, thanks to it's brushless motor and ESC. This power and its stability means it will work brilliantly in windy conditions too.
The Focus EP 400 not only looks good and realistic, but it is well made, strong and built for crash resistance, so you can fly with confidence.
** This plane is available in either yellow, or blue. We are stocking the blue variant, though some of the pictures here show the yellow model.

The Focus 400 is fitted with a brushless motor, which has several advantages over the brushed type. They are more efficient and reliable, make less noise, haver a longer lifetime, and most importantly they deliver more power! Added together this gives your aeroplane better capabilities for performing 3D aerial stunts.

Specs
Overall Length: 774.7mm
Wing Span: 965mm
Wing Area: 17.3dm2
Fly Weight: 455g
Wing Loading: 17.3g/dm2
Drive System: Brushless Motor (1250kv)
Servo: 3X 9g High Speed Micro Servos
Speed Controller: 18A Brushless ESC
Battery: 11.1V 1250mAh Li-Polymer
Control: 4 CH Multi-functional FM Radio and 6 CH Micro Receiver
Range: 1000m

Features
Construction: All foam
Wings: 1 pc wing with ailerons
Cowling: Plastic
Canopy: Clear plastic
Cockpit Features: Moulded foam
Landing Gear: Main and nose
Aileron Control: Single servo
Hardware: All necessary hardware included
Motor Mount: Plastic

]]>

4CH Accipiter Badius Electric Radio Control 35Hz Brushed Plane

Fri, 19 Feb 2010 19:59:51 +0000

]]>

Accipiter Badius is the latin name of a species of raptor, a bird of prey known for its fast manoeuvring ability, and this naming should give a clue as to the capabilities of this plane. You can tell by looking at it, that it has been designed with aerobatics in mind!

This plane has a 35Hz controller and brushed motor options, making it an affordable entry level outfit, ideal for someone wanting to buy their first plane. Additionally the Accipiter Badius is almost ready to fly straight from the box with all its electronic components pre-installed at the factory. Within a few minutes of opening the box, you can have this plane powering across the sky.

The controller gives the plane a good 500m range and you can enjoy around fifteen minutes flying from one charge of the battery.

Specs
Length: 900mm
Wing span: 900mm
Wing area: 13.8dm sq
Weight: 380g
Wing loading: 27.5g/dm sq
Battery: Ni-MH 8.4V-600mAh
Power: 370 brushed motor
Control: 4 ch radio system
3 mini servos and ESC
Range: 500m
Flying time: approx 15 minutes

Features
4 CH Full RC - Aileron, Elevator, Rudder, Throttle
Full aerobatic characteristics
Ready to Fly in Just Minutes!
Tough and lightweight
Pre-installed Electronics
Suitable for beginners and experts

]]>

Sonic 185 Brushless 4CH 2.4G Brushless RC Glider

Fri, 19 Feb 2010 19:50:16 +0000

]]>

The Sonic 185 is an excellent choice of 'next' plane for pilots, who feel that they have mastererd the rudiments of radio contolled flight, though suitable for beginners too. The Sonic has a 1.85 metre wingspan and a powerful brushless motor with LiPo batteries. With this model you can turn off the motor, then soar down slopes and climb with the thermals to enjoy the experience of truly silent flight.

Made from the same crash resistant foam material as other planes in the Dynam range, the Sonic is factory finished, complete with a 4 channel receiver which allows full control of the rudder, elevator, ailerons and throttle. For easier transportation, the Sonic has a split wing design and a carbon fibre wing joiner.

Free FMS flight simulator freeware is supplied together with a USB interface cable to connect your transmitter directly to your computer. Everything that you need is in the box, apart from 8 AA batteries.

The Sonic 185 comes with a 2.4G radio which means the range is longer and more stable plus you do not have to worry about interference from other fliers. The plane is made from strong but lightweight foam that is more resistant to crashes and gives easier stable flight even in windy conditions.

Specs
Wing Span: 1850mm
Length: 1090mm
Weight RTF: 980g
Electric Motor: Brushless 200W
Battery: 11.1V 1800mAh 15C Li-Po
ESC: 35A
Radio: 4CH, 4 Servos (9g)

Features
Sonic 185 4CH Remote Control Plane
Brushless 200W Motor
4-CH FM Transmitter Receiver
Motor, ESC, and 4 Servos pre-installed
Mains Power Supply for charger
Automatic Li-Po Balance Charger
High power Li-Po battery 11.1V1800mAh

]]>

Liebao 4CH Powered RC Glider Brushed 35Hz Folding Propeller

Fri, 19 Feb 2010 15:54:20 +0000

]]>

The Liebao glider is a gracefully designed plane with the advantage of it having a motor which can be used to get it into the air, before turning it off to enjoy silent, powerless flight. The Liebao is suitable for all, beginners and experts will find it both entertaining and interesting to fly.

It is robustly built and designed to withstand those inevitable crashes experienced as you learn to handle the craft; even its propellers fold backwards to minimise the risk of impact damage! The propeller also collapses during gliding to increase the streamlining of the plane.

Specs
Wing span: 800mm
Length: 670mm
Weight: 640g
Battery: 8.4v-650mAh NI-MH
Power: 380 brushed motor
4channel TX and RX
2*9g servo,
1*25A brush ESC
Flying weight:400g

Features
Flying time: approx. 15 mins
Flying height: approx. 300m
Range: 500m
Folding propeller

]]>

EZ Hawk Electric 3 Channel RTF Brushless Trainer Plane

Fri, 19 Feb 2010 15:42:41 +0000

]]>

Dynam EZ Hawk with its brushless motor is the perfect trainer for beginners. Only a small amount of assembly is required once the box is opened and you'll by flying this plane in minutes!

The EZ Hawk powered trainer is constructed from a durable EPO foam, so it can take the knocks and crashes as you learn to use it to its full capability. The EZ Hawk is propelled by a powerful Dynam Speed 400 brushless motor run off a Dynam Brushless Electronic Speed Control (ESC). This combination of power and control makes it an excellent aerobatic craft.

It comes with a Li-Po battery and charger for longer flights.

The EZ Hawk is fitted with a brushless motor, which has several advantages over the brushed type. They are more efficient and reliable, make less noise, haver a longer lifetime, and most importantly they deliver more power! Added together this gives your aeroplane better capabilities for performing 3D aerial stunts.

Specs
Wing span :1370mm
Length : 870mm
Weight : 680g
Charger: 3 Cell Li-po balance charger
Transmitter: NE-KO4 FM 4 channel
Receiver: Dynam 72Mhz 5CH receiver
Servos: 9g micro servos (3pcs)

Features
EZ Hawk plane inc. undercarriage and prop
Electronic Speed Controller
Dynam Speed 400 Brushless Motor
Tx and Rx crystals 72 Mhz
Battery: 11.1v 1250mah Li-Po battery.

]]>

Hawk Sky 4 Ch Brushless Sport Trainer 2.4G

Fri, 19 Feb 2010 15:30:16 +0000

]]>

Dynam Hawksky with its brushless motor is the perfect trainer for beginners, who want a plane that they can learn on, but is also capable of impressive stunts as their skills develop. Only a small amount of assembly is required once the box is opened and you'll by flying this trainer in minutes!

The Hawksky plane is constructed from a durable EPO foam, so it can take the knocks and crashes as you learn to use it to its full capability. The Hawk Sky is propelled by a powerful Dynam Speed 400 brushless motor run off a Dynam Brushless Electronic Speed Control (ESC). This combination of power and control makes it an excellent aerobatic craft.

It comes with an Li-po battery and charger for longer flights.

The Hawksky comes with a 2.4G radio which means the range is longer and more stable plus you do not have to worry about interference from other fliers. The plane is made from strong but lightweight foam that is more resistant to crashes and gives easier stable flight even in windy conditions. The plane can take off from the ground or can be hand launched.

Specs
Wing span :1370mm
Length : 917mm
Fuselage length: 870mm
Weight : 600g
Wing area: 22.8dm2
Charger: 3 Cell Li-po charger
Transmitter: NE-KO4 FM 4 Ch
Receiver: 72Mhz 5CH receiver Servos: Dynam 8.4g micro servos (4pcs)
ESC: Brushless Electronic Speed Controller

Features
Hawk Sky plane inc undercarriage and propeller
Dynam 3 Cell standard Li-po charger
Brushless Electronic Speed Controller
Dynam Speed 400 Brushless Motor
Tx and Rx crystals 72 Mhz

]]>

Snow Bird RC 4ch Electric Brushless RC Aeroplane

Fri, 19 Feb 2010 15:24:25 +0000

]]>

This is the latest Snow Bird plane from Dynam, with an upgraded 4 channel receiver instead of the earlier 3 channel model, allowing more control and more impressive 3D aerial stunts and aerobatics, while at the same time being easy for a beginner to control. Everything apart from the batteries is included in the box and you can have the craft in the air within minutes of opening it, without need for tools or glue!

This plane is suitable for all, from novice pilots to those with much more experience. To cope with the rigours of being used to learn on it has a tough plastic and foam construction and even comes with two sets of wings, a thick one for beginners, and a thinner one for experienced pilots. The wings are reinforced with a carbon rod, for additional robustness.

The Snow Bird is fitted with a brushless motor, which has several advantages over the brushed type. They are more efficient and reliable, make less noise, haver a longer lifetime, and most importantly they deliver more power! Added together this gives your aeroplane better capabilities for performing 3D aerial stunts.

Specs
Wingspan: 880mm
Overall Length: 740mm
Wing Area: 11.3dm2
Wing Loading: 31.9g/dm2
Flying Weight: 360g
Motor: 400 Direct Drive brushed motor
Servo: 2X 9g servos
Battery: 7.2V 650mAh Ni-MH
Control: 3 CH FM Radio Transmitter and Receiver
Range: 2000 feet

Features
Aeroplane (90% assembled)
2 Main Wing Sets
4 Channel FM Radio Transmitter
Wall Battery Charger
High Quality Rechargeable 7.2V 650mAh Ni-MH Battery
USB Simulation Cable
English Manual

]]>

F9F Panther 2.4GHz 4 CH RC EDF Fighter Jet 64mm

Thu, 18 Feb 2010 14:25:54 +0000

]]>

The Grumman F9F Panther was one of the U.S. Navy's first successful carrier-based jet fighters. Introduced in 1958 the Panther was the most widely used US Navy jet fighter of the Korean War, flying 78,000 sorties and scoring the first air-to-air kill by the US Navy in the war, the downing of a North Korean Yakovlev Yak-9 fighter.

Capable of 575mph and with a range of 1,300 miles, this jet had quite a thirst for fuel. As there was insufficient space within the wings and fuselage for the amount of fuel required, permanently-mounted wingtip fuel tanks were added which had the side benefit of improving the fighter's rate of roll! The jet was retired by the US in the late fifties to early sixties, but was still in service with the Argentinian Navy (the only foreign buyer of the Panther) until 1969.

Like all the planes in the Starmax range, the Panther is finished in the factory to a high standard and represents an excellent replica of the real aircraft. Extra features like the realistic landing gear, and the clear cockpit complete with pilot add to the authenticity and realism present in this model.

But! Looks are only half of the story with these models. In the air, it is an incredible acrobat, and capable of over 90mph. It is launchable by hand or will take off from the ground with ease. As you can no doubt imagine, this package of power and size, makes for an extremely agile aeroplane; this fighter has an amazing 3D aerobatic repertoire in experienced hands with a tremendous roll rate and an ability to climb vertically at incredible speed. The videos show you just how capable the F9F is! If you're really good you will be able to perform the famous 'Cobra Manoeuvre' with this jet.

Specs
Wingspan: 770mm
Length: 793mm
Flying Weight: 520g
Radio System: 4Ch Tx and 6 Ch Rx ,
Four 9 gram servos
64mm Ducted fan
Brushless motor and 25A ESC
Battery: 1300Mah, 11.1V

]]>

F-4E Phantom II 2.4GHz RC EDF Fighter Jet 64mm

Thu, 18 Feb 2010 14:19:10 +0000

]]>

The F-4E Phantom II is a tandem two-seat, twin-engined, all-weather, long-range supersonic jet interceptor fighter/fighter-bomber originally developed for the U.S. Navy. First entering service in 1960, the Phantom continued to form a major part of U.S. military air power throughout the 1970s and 1980s, and even now are in active service with a number of other countries.

Despite the imposing dimensions and a maximum takeoff weight of over 27,000 the F-4E had a top speed of Mach 2.23 and an initial climb of over 41,000 ft/min. Shortly after its introduction, the Phantom set 15 world records, including an absolute speed record of 1,606.342 mph and an absolute altitude record of 98,557 ft.

The F-4 had several variants, but this model the F-4E was the one chosen by The Thunderbirds, who are the air demonstration squadron of the U.S. Air Force.

Like all the planes in the Starmax range, the Phantom has lots of detail, a great factory finished look, with a clear canopy with cockpit, the landing gear are easy to remove and replace, and the whole model has been designed for easy fan access for maintenance.

In the air, it's phenomenal, capable of around 70mph, which for something less than 80cms long is very fast indeed. It is launchable by hand or will take off from the ground with ease. As you can no doubt imagine, this package of power and size, makes for an extremely agile aeroplane; this fighter has an amazing 3D aerobatic repertoire in experienced hands with a tremendous roll rate and an ability to climb vertically at incredible speed. The videos show you just how capable the F-4E is!

Specs
Wingspan: 542mm
Length: 788mm
Flying Weight: 540g
Wing area: 8dm2
Wing Load: 67g/dm2
Radio System: 4Ch Tx and 6 Ch Rx ,
Four 9 gram servos
64mm Ducted fan
Brushless motor and 25A ECS
Battery: 1300Mah, 11.1V

Features
Pre-painted foam fuselage & wings
Pre-installed electrics
CAD engineering quality
Retractable landing gear
Stunning paintwork
64mm electric ducted fan
State of the art components
2.4G Transmitter
Can perform amazing aerobatics
Is capable of the 'Cobra Manoeuvre'
Range: 1000m

]]>

He 162 Salamander 2.4GHz RC EDF Fighter Jet 64mm

Thu, 18 Feb 2010 14:12:00 +0000

]]>

Heinkel's He 162 Volksjäger ("People's Fighter") was a German single-engine, jet-powered fighter aircraft used by the Luftwaffe in WWII. The original 162 was constructed mainly from wood as metals were in short supply and prioritised for other aircraft. Despite this the He 162 was the fastest of the first generation of Axis and Allied jets. Volksjäger was the Reich Air Ministry's official name for the He 162. Other names given to the plane include Salamander, which was the codename of its construction program. It took less than 90 days from the final design being chosen to a finished aircraft actually flying!

The He 162 is a clean, sporty-looking little aircraft, with a sleek, streamlined fuselage. The BMW jet was mounted in a pod situated on top of the fuselage directly aft of the cockpit. Twin vertical tailfins were mounted at the ends of the upswept tailplanes to clear the jet exhaust, a high-mounted straight wing with a forward-swept trailing edge and shallow dihedral, an ejection seat was provided for the pilot (deemed far more valuable than the machine itself), and tricycle landing gear that retracted into the fuselage.

This scale model of the He 162 has been carefully designed using CAD technology and, is a faithful replica of the World War II original. All parts are pre-painted to a high level of detail, the aeroplane looks amazing! As an added bonus it's 95% complete straight out of the box, with only a few stages of assembly to complete before you can take to the air.

This plane is a stable model and has a well chosen, powerful motor for its size; you only need to give it a little touch of throttle and this warbird will be off, skywards. It will take off either from the ground or can be launched from the hand, and when it is launched, the fighter takes to the air with ease, and looks extremely realistic in the air.The He 162 can perform a whole host of aerobatics in skilled hands, but due to its stability it is a suitable choice of aeroplane for someone wishing to learn the thrills of model jets.

Specs
Wing span: 790mm
Length: 988mm
Flying Weight: 600g
Wing Load: 47g/dm²
Wing area: 12.8dm²
Radio System: 4Ch Tx and 6 Ch Rx
Four 9 gram servos Brushless motor
25A ESC
Battery: 3 Cell Li-Po ,1300 mAh,11.1V

Features
Pre-painted foam fuselage & wings
Pre-installed electrics
CAD engineering quality
Retractable landing gear
Stunning paintwork
64mm electric ducted fans
State of the art components
2.4G Transmitter
Can perform amazing aerobatics
Range: 1000m

]]>

F-35 Lightning II 2.4GHz RC EDF Jet

Thu, 18 Feb 2010 13:00:52 +0000

]]>

The Lockheed Martin F-35 Lightning II is a, single-seat, single-engine, stealth multirole fighter, that can perform close air support, tactical bombing, and air defense missions. The F-35 is intended to be the world's premier strike aircraft and to be active until 2040, with close and long-range air-to-air capability.

The F-35 is required to be four times more effective than existing fighters in air-to-air combat, eight times more effective in air-to-ground combat, and three times more effective in reconnaissance and suppression of air defenses all while having better range and requiring less logistics support! The first flight of the F35 was in 2006.

This scale model of the F-35 has been carefully designed using CAD technology and, this is evident in the realistic and high quality finish seen in this plane. All parts are pre-painted to a high level of detail, the jet really does look fantastic, and as an added bonus it's 95% complete straight out of the box, with only a few stages of assembly to complete before you can take to the air.

This plane is incredibly stable and has well proportioned, controllable power; you only need to nudge the throttle gently and the F35 will shoot down your runway and take off. It will take off either from the ground or can be launched from the hand, and when it is launched, the F35 accelerates like a rocket and takes to the air with ease, and looks absolutely awesome when in flight.The Lightning can perform a whole host of aerobatics in skilled hands, but due to its stability it is a suitable choice of aeroplane for someone wishing to learn the thrills of model jets. That said, this plane can do in excess of 90mph!!

This jet comes with a 2.4G radio which means the range is longer and more stable plus you do not have to worry about interference from other fliers. The plane is made from strong but lightweight foam that is more resistant to crashes and gives easier stable flight even in windy conditions. This aeroplane can take off from the ground or can be hand launched.

Specs
Wing span: 608mm
Length: 840mm
Flying Weight: 600g
Wing Load: 57g/dm2
Wing area: 8.7dm2
Radio System: 4Ch TX and 6 Ch Rx,
Three or Five 9 gram servos
Brushless motor and 25A ESC
Battery: 3 Cell Li-Po, 1300 mAh, 11.1V

]]>

F 18E Jolly Rogers RC EDF Jet 2.4G 64mm

Thu, 18 Feb 2010 12:50:49 +0000

]]>

The F/A-18 known as the Hornet is a supersonic, all-weather, carrier-capable, multirole fighter jet, designed to attack both ground and aerial targets. Introduced in the early 80s and capable of Mach 1.8 (1,190mph) at 40,000 feet, it is still in active service around the world in roles such as fighter escort, fleet air defense, suppression of enemy air defenses (SEAD), air interdiction, close air support and aerial reconnaissance. The F/A-18E has been a popular choice of fighter for aircraft carrier deployment.

Strike Fighter Squadron 103 (VF-103), nicknamed the Jolly Rogers is an aviation unit of the United States Navy established in 1952. They fly the Hornet emblazoned with a sinister skull and cross bones on the tailfins, and it is these planes that have been reproduced in the model you see here.

This scale model of the real thing has been beautifully crafted using CAD technology and, this is evident in the realsitic and high quality finish seen in this plane. All parts are pre-painted to a high level of detail, the jet really does look fantastic, and as an added bonus it's 95% complete straight out of the box, with only a few stages of assembly to complete before you can take to the air.

This plane is incredibly stable and has just the right amount of power; only a couple of flicks of the throttle are needed to get this jet taxiing and ready for take off. The Jolly Rogers model accelerates like a rocket and takes to the air with ease, and once in the air, that's when the fun begins! The F/A 18E can perform pretty much any aerial acrobatic manoeuvre you could possibly ask of it, but due to its stability it is a suitable choice of aeroplane for someone wishing to learn the thrills of model jets.

Specs
Wing span: 686mm
Length: 980mm
Flying weight: 560g
Wing area: 10dm²
Wing Load: 56g/dm²
Radio System: 4Ch Tx and 6 Ch Rx
Four 9 gram servos
Brushless Powered: Powerful 15L inner runner brushless motor and 25A ESC Battery: 3 Cell Li-Po Battery,1300 mAh,11.1V

Features
Pre-painted foam fuselage & wings
Pre-installed electrics
CAD engineering quality
Retractable landing gear
Stunning paintwork
Foam missiles
64mm electric ducted fan
State of the art components
2.4G Transmitter
Can perform amazing aerobatics
Is capable of the 'Cobra Manoeuvre'
Range: 1000m

]]>

F 18E Tiger RC EDF Jet 2.4G 64mm

Thu, 18 Feb 2010 12:10:41 +0000

]]>

This plane is incredibly stable and has just the right amount of power; only a couple of flicks of the throttle are needed to get this jet taxiing and ready for take off. The Tiger accelerates like a rocket and takes to the air with ease, and once in the air, that's when the fun begins! The F/A 18E can perform pretty much any aerial acrobatic manoeuvre you could possibly ask of it, but due to its stability it is a suitable choice of aeroplane for someone wishing to learn the thrills of model jets

]]>

Yakovlev Yak-9D

Sun, 31 Jan 2010 20:07:14 +0000

]]>

The Yak-9D from 1944 was an extended range version of the succesful type operational over Stalingrad in late 1942, being able to escort heavy bombers.

Specification
Model Scale - 1:72
Number of Parts - 30
Dimensions (mm) - L188 x W139
Skill Level - 1
Airfix Flying Hours - 1
Requires Painting - Yes

]]>

Westland Lysander

Sun, 31 Jan 2010 19:49:31 +0000

]]>

Using its famous short take-off and landing characteristics (STOL), the Lysander was ideal for its early role as a reconnaissance and artillery spotting plane, and even more famously for transporting Allied agents into and out of occupied Europe.

Specification
Model Scale - 1:72
Number of Parts - 49
Dimensions (mm) - L129mm x W211mm
Skill Level - 2
Airfix Flying Hours - 1
Requires Painting - Yes

]]>

Saab Draken

Sun, 31 Jan 2010 19:46:18 +0000

]]>

Over 500 of these interceptor and strike aircraft have been delivered to the Swedish airforce. It can fly at mach 2 - twice the speed of sound.

Specification
Model Scale - 1:72
Number of Parts - 53
Dimensions (mm) - L216mm x W130mm
Skill Level - 2
Airfix Flying Hours - 1
Requires Painting - Yes

]]>

Royal Aircraft Factory R.E.8

Sun, 31 Jan 2010 19:42:18 +0000

]]>

Serving as a rugged and relaible reconnaisance aircraft the RE8 served with the Royal Flying Corps until the end of the "Great War"

Specification
Model Scale - 1:72
Number of Parts - 33
Dimensions (mm) - L118 x W180
Skill Level - 1
Airfix Flying Hours - 1
Requires Painting - Yes

]]>

One Small Step For Man Gift Set

Sun, 31 Jan 2010 19:38:00 +0000

]]>

The Lunar Module was the Apollo spacecraft that landed on the moon and returned to lunar orbit. It consists of the Descent and Ascent stages. The Descent stage contains the landing gear, descent rocket engine and fuel to land on the moon, as well as all the equipment needed by the Astronauts whilst on the moon's surface. As the missions developed more sophisticated equipment was carried and is part of this set The Ascent stage contains, amongst other vital equipment, the crew cabin; environmental control (life support) system; overhead hatch/docking port; ascent rocket engine; and enough fuel, battery power, and breathing oxygen to return to lunar orbit and rendezvous with the Apollo Command and Service Module. This kit includes eight acrylic paints, two paint brushes and glue..

Specification
Model Scale - 1:72
Number of Parts - Lunar Module: 92 - Figures:16
Dimensions (mm) - Lunar Module: L100 x W100 x H92 - Diorama Base: L348 x W247
Skill Level - 2
Airfix Flying Hours - 3
Requires Painting - Yes

]]>

Messerschmitt BF109G

Sun, 31 Jan 2010 19:35:42 +0000

]]>

Over 12,000 of the "Gustav" G-6 were built from 1943 to 1944 and were armed with two formidable 13mm machine guns, enabling the top Luftwaffe aces to record in some cases hundreds of "kills".

Specification
Model Scale - 1:72
Number of Parts - 41
Dimensions (mm) - L125 x W137
Skill Level - 1
Airfix Flying Hours - 1
Requires Painting - Yes

]]>

Messerschmitt BF109E

Sun, 31 Jan 2010 19:33:41 +0000

]]>

The Me BF109e was the Luftwaffe's main fighter during the Battle of Britain when it was pitted against the new fighters of the RAF.

Specification
Model Scale - 1:24
Number of Parts - 146
Dimensions (mm) - L360mm x W425mm
Skill Level - 4
Airfix Flying Hours - 5
Requires Painting - Yes

]]>

Martin B-57B Canberra

Sun, 31 Jan 2010 19:31:46 +0000

]]>

The B-57 was the US built version Canberra which first saw action in the Vietnam War. It developed into many variants serving many crucial roles. The Martin B-57B Canberra will offer parts and declas for U.S.A.F versions, the B-57B, RB-57E and RB-57G.

Specification
Model Scale - 1:48
Number of Parts - 120
Dimensions (mm) - L406 x W416
Skill Level - 3
Airfix Flying Hours - 4
Requires Painting - Yes

]]>

Henschel Hs123A-1

Sun, 31 Jan 2010 19:29:50 +0000

]]>

Designed as the Luftwaffes first dive bomber, the Henschel Hs 123A-1 saw service in the Spanish Civil War and in the campaigns in Poland, Belgium, France and Russia where their effectiveness and popularity continued due to their rugged design and reliability

Specification
Model Scale - 1:72
Number of Parts - 38
Dimensions (mm) - L116 x W146
Skill Level - 2
Aifix Flying Hours - 1
Requires Painting - Yes

]]>

Hawker Sea Fury FB.11

Sun, 31 Jan 2010 19:27:21 +0000

]]>

When the Korean War broke out in 1950, the Sea Fury was the Fleet Air Arm's leading single-seat fighter, and it fought with great distinction during the conflict. On 9 August 1952 a Flight of Sea Furies from 802 squadron one MiG 15 and badly damaged two others without incurring any damage to their own aircraft, even though the MiGs had a 200 m.p.h speed advantage.

Specification
Model Scale - 1:72
Number of Parts - 44
Dimensions (mm) - L156 x W162
Skill Level - 1
Aifix Flying Hours - 1
Requires Painting - Yes

]]>

Hannover CLIII

Sun, 31 Jan 2010 19:22:47 +0000

]]>

The Hannover, as a single-engined aircraft, was unique in having a biplane tail. Its purpose was to reduce the tailplane span, thereby affording a wider field of fire for the observer/gunner, and entered service in 1917.

Specification
Model Scale - 1:72
Number of Parts - 31
Dimensions (mm) - L117 x W162
Skill Level - 1
Airfix Flying Hours - 1
Requires Painting - Yes

]]>

FMA IA 58A Pucara

Sun, 31 Jan 2010 19:20:50 +0000

]]>

In the 1982 War, apart from Port Stanley airport, Pucarás were also operated from two small grass improvised airfields at Goose Green and Pebble Island. They were used in the reconnaissance role and shot down a Royal Marines Scout on May 28, the only confirmed Argentine air-to-air victory of the war.

Specification
Model Scale - 1:72
Number of Parts - 93
Dimensions (mm) - L198 x W201
Skill Level - 2
Airfix Flying Hours - 1
Requires Painting - Yes

]]>

Douglas Devastator

Sun, 31 Jan 2010 19:18:44 +0000

]]>

Prior to Pearl Harbour and the United States war with Japan, the Devastator equipped the U.S. Navys Torpedo Squadrons and the type took part in all the major sea battles in the early months following the devastating attack of December 1941

Specification
Model Scale - 1:72
Number of Parts - 75
Dimensions (mm) - L148 x W211
Skill Level - 2
Airfix Flying Hours - 1
Requires Painting - Yes

]]>

De Havilland Mosquito NFII/FBVI

Sun, 31 Jan 2010 19:16:39 +0000

]]>

The "NF" variants of the Mosquito were designed for night time operations in particular, and this spectacular model will show off this all-time classic RAF aircraft in all its glory, with full interior detail, removable panels, and every part meticulously researched and moulded, enabling any modeller to produce possibly the most exquisite model in any collection.

Specification
Model Scale - 1:24
Number of Parts - 617
Dimensions (mm) - L522 x W688
Skill Level - 4
Airfix Flying Hours - 6
Requires Painting - Yes

]]>

Dassault Mirrage III Starter Set

Sun, 31 Jan 2010 19:15:01 +0000

]]>

This extremely versatile and successful aircraft is a multipurpose all-weather ground attack aircraft that can also operate from grass airstrips, to carry a range of weapons and long-range fuel tanks. This kit includes six Humbrol acrylic paints, two paint brushes precision glue.

Specification
Model Scale - 1:72
Number of Parts - 39
Dimensions (mm) - L204 x W114
Skill Level - 1
Airfix Flying Hours - 1
Requires Painting - Yes

]]>

Dassault Mirage F.1

Sun, 31 Jan 2010 19:12:15 +0000

]]>

Dassault designed the Mirage F1 as the successor to its Mirage III and Mirage 5 fighters. Unlike its predecessors, it has a swept wing mounted high on the fuselage, as well as a conventional tail surface. Although it has a smaller wingspan than the Mirage III, the F1 nevertheless proved to be clearly superior to its predecessor. It can carry up to 40% more fuel, has a shorter take-off run, a superior range in lo-lo missions, and better manoeuvrability.

Specification
Model Scale - 1:72
Number of Parts - 72
Dimensions (mm) - L210 x W117
Skill Level - 2
Airfix Flying Hours - 2
Requires Painting - Yes

]]>

D.H. Mosquito MkII/VI/XVIII

Sun, 31 Jan 2010 19:06:20 +0000

]]>

The Mosquito attained the reputation of being one of the most outstanding aircraft of WWII. Constant successes in it's various fighter bomber, maritime and ground attack roles made it a very respected foe by its opponents. It's wooden construction provided resistance to punishing damage and afforded quick repair.

Specification
Model Scale - 1:72
Number of Parts - 97
Dimensions (mm) - L171mm x W228mm
Skill Level - 2
Airfix Flying Hours - 1
Requires Painting - Yes

]]>

Boeing AH-64 Longbow Apache

Sun, 31 Jan 2010 19:03:53 +0000

]]>

The Hughes Apache entered service with the US Army bringing with it advanced technology to the concept of airbourne battlefield support.

Specification
Model Scale - 1:72
Number of Parts - 172
Dimensions (mm) - L310 x W305
Skill Level - 2
Airfix Flying Hours - 1
Requires Painting - Yes

]]>

BAe Nimrod Limited Edition

Sun, 31 Jan 2010 19:01:54 +0000

]]>

The Nimrod is a Limited Edition Kit, please see History for more information. Nimrod is the worlds only jet maritime reconnaissance aircraft and submarine hunter. The Aircraft has been in service witht he RAF for over three decades and has flown in a number of conflicts around the world, including the Falklands War, two Gulf Wars and other troubled spots. Given four sidewinder air-to-air missiles in the first Gulf War, it could be said that Nimrod became the largest fighter in the world and it can now fly up to maximum speeds of 575mph powered by four Rolls Royce Spey engines. Please see History for more information.

Specification
Model Scale - 1:72
Number of Parts - 249
Dimensions (mm) - L487 x W537
Skill Level - 3
Airfix Flying Hours - 5
Requires Painting - Yes

]]>

BAC Aerospatiale Concorde

Sun, 31 Jan 2010 19:00:15 +0000

]]>

A passenger airliner designed to fly at twice the speed of sound (Mach 2.05), first flown in 1969, Concorde service commenced in 1976 and continued for 27 years. It regularly flew from London Heathrow (BA) to New York JFK and Washington Dulles. It set many records, including circumnavigating the world in the time of 31 hours and 27 minutes 49 seconds flight, on 16 August 1995. She had an average cruise speed of Mach2.02 (about2,140km/h) with a maximum cruise altitude of 60,000 feet (18,300 metres).

Specification
Model Scale - 1:72
Number of Parts - 90
Dimensions (mm) - L865mm x W355mm
Skill Level - 3
Airfix Flying Hours - 4
Requires Painting - Yes

]]>

1/16 Panther G Radio Controlled Tank - PRO VERSION

Fri, 29 Jan 2010 11:27:09 +0000

]]>

The Panther G was developed in response to the Russian T-34 and was one of the best tanks of WWII. The Ausf G was important as it was the final version of this famous tank series and it had a big influence on post-war tank design. Early versions suffered from mechanical problems due to lack of adequate testing. Produced until 1945 it saw action on all fronts in the war. The 75mm gun had excellent anti-armor capability and it could out duel T-34s at long range. The excellent suspension system meant it could traverse rough terrain at speed. Over 5900 were built and the tank served with the French army after the war. This fantastic scale radio controlled replica from Heng Long looks great and is feature packed. The tank fires plastic bbs and is the pro version with metal tracks and parts, a built in real smoke generator and sound effects. Sound effects include emulation music, motor start-up, engine, machine-gun and cannonball when it fires a bb. Please note this tank comes in two different finishes, camo and grey.

All functions of the rc tank are controlled from the included transmitter. The tank can go forward and backward at two different speeds and the real working tracks mean it can be rotated any way. The turret is also fully controllable and can be rotated as well as moving the gun up and down. The tank has working suspension for climbing over objects and up hills. The pro version has also been upgraded with a metal gearbox making it more powerful and reliable.

Requires:
8 AA Batteries for Transmitter

Specifications:
Storage Capacity: 40 BB's
Length: 52 cm
Width: 24 cm
Height: 20 cm
Scale: 1:16
Battery: 7.2V with charger
Climbing Gradient: (Changeable on different road surfaces) Apr. 35-degree

FEATURES
Built in realistic smoke generator
Highly detailed realistic model
Metal tracks
Metal wheels
Metal gearbox
Demonstration mode
Frequencies can be changed so multiple tanks can be used together
Super chassis, realistic suspension system, rubber covered wheels, pre-assembled tracks
A realistic commander is included
Rotating turret
Gun can be moved 30 degrees up and down
Full control of tank movement - forward, backward, rotate left and right
Many sound effects - Emulation music, motor start-up sound, Engine sound, machine-gun sound, Cannonball sound
Adjustable sound

]]>

1/16 DAK Pz.Kpfw.IV RC Tank - PRO VERSION

Fri, 29 Jan 2010 11:22:11 +0000

]]>

The German Afrikakorps (German: Deutsches Afrikakorps or DAK) that used this version of the Panzer tank was the German expeditionary force in Libya and Tunisia during the North African Campaign of World War II. The force was kept as a distinct formation and became the main German contribution to Panzer Army Africa which evolved into the German-Italian Panzer Army. In April 1941 production of the Panzer IV Ausf. F started. It featured 50-millimetre single-plate armor on the turret and hull and a further increase in side armor to 30 millimetres. The weight of the vehicle was now 22.3 tonnes, which required a corresponding modification of track width from 380 to 400 millimetres to reduce ground pressure. The wider tracks also facilitated the fitting of ice sprags, and the rear idler wheel and front sprocket were modified. A total of 464 Ausf. Fs were produced from April 1941 to March 1942. This fantastic scale radio controlled replica from Heng Long, finished in the DAK colours and design, looks great and is feature packed. The highly detailed finish adds to the realism and the included commander figure completes the model perfectly. The tank fires plastic bbs and is the pro version with metal tracks and parts, a built in real smoke generator and sound effects. Sound effects include emulation music, motor start-up, engine, machine-gun and cannonball when it fires a bb.

Requires:
8 AA Batteries for Transmitter

Specifications:
Storage Capacity: 40 BB's
Length: 36 cm
Width: 18.5 cm
Height: 17.5 cm
Scale: 1:16
Battery: 7.2V with charger
Climbing Gradient: (Changeable on different road surfaces) Apr. 35-degree

]]>

1/16 Panther Radio Controlled Tank - PRO VERSION

Fri, 29 Jan 2010 11:16:19 +0000

]]>

The Panther, next to the Tiger is the best-known German tank of World War II. The Panther and the Soviet T-34 are considered to be the best tanks of World War II. Panthers technical design incorporated many features of the T-34, such as wide tracks for better traction and improved cross-country performance, a powerful engine, a hard-hitting long-barrelled 75mm gun, and sloping armor for extra protection. The Panther was the first German-made tank with sloping armor. Although its design was in some ways similar to the T-34, the Panther was larger, heavier, and different in many technical aspects. The Panther had large overlapping road wheels and a state-of-the-art suspension system that enabled it to traverse rough terrain at high speed. The main gun was a 7.5 cm Rheinmetall-Borsig KwK 42 with 79 rounds with semi-automatic shell ejection. The Panther's gun was one of the most powerful tank guns of WWII, due to the large propellant charge and the long barrel, which gave it a very high muzzle velocity and excellent armor-piercing qualities. The tank had normally two MG 34 machine guns of a specific version designed for use in armored combat vehicles featuring an armored barrel sleeve. An MG 34 machine gun was located co-axially with the main gun on the gun mantlet; an identical MG 34 was located on the glacis plate and fired by the radio operator.

This fantastic scale radio controlled replica from Heng Long looks great and is feature packed. The highly detailed finish adds to the realism and the included commander figure completes the model perfectly. The tank fires plastic bbs and is the pro version with metal tracks and parts, a built in real smoke generator and sound effects. Sound effects include emulation music, motor start-up, engine, machine-gun and cannonball when it fires a bb.

Requires:
8 AA Batteries for Transmitter

Specifications:
Storage Capacity: 40 BB's
Length: 52 cm
Width: 24 cm
Height: 20 cm
Scale: 1:16
Battery: 7.2V with charger
Climbing Gradient: (Changeable on different road surfaces) Apr. 35-degree

]]>

1/16th Bulldog Smoking RC Tank - Pro Version

Fri, 29 Jan 2010 11:11:38 +0000

]]>

This is the new pro version tank from Heng Long. Like the standard Heng Long 1/16th tanks it has all the great features of a top of the range BB tank such as firing sounds, built-in real smoke generator, bb firing, simulative motor start-up sounds, engine sounds, machine-gun sounds and cannon ball sounds. The difference though is that the pro versions are upgraded to make them even stronger and perform better with metal parts.

The most important change on this pro version is the gearbox that has been replaced with a metal gearbox with metal gears. This makes the tank tougher and more reliable. The plastic tracks and wheels have also been replaced with metal tracks and wheels. Not only does this make them stronger but they also look fantastic and add to the realism of the model.

On the right you can see the metal tracks but also the Bulldog's exhaust. The Bulldog has a real smoke generator and when used real smoke comes out of this exhaust which looks amazing.

The Bulldog is almost 2 feet in length! This tank is fully functional with multi-directional driving (and it's fast!), 360 degree turret swivel and the barrel raises and lowers. This tank has a bb gun that shoots standard 6mm BBs and a capacity of 40 pellets.

Have a full-on battle with up to 2 of your friends and see who will become the Air soft Battle Tank Champion. Each Snow Leopard Tank can be switched between 3 different channels so the controls do not interfere with each other.

]]>

1/16 Jagdpanther Radio Controlled Tank With Smoke And Sound

Fri, 29 Jan 2010 11:05:57 +0000

]]>

The Jagdpanther (German: "hunting panther") was a tank destroyer built by Nazi Germany during World War II based on the chassis of the Panther tank. Many military historians consider the Jagdpanther to be one of the best tank destroyers of the war due to the combination of the 8.8 cm KwK 43 of the Tiger II and the proven Panther chassis. The Jagdpanther had a good power-to-weight ratio and a powerful main gun, which enabled it to destroy any type of Allied tank. Because it was based on the existing Panther chassis, the vehicle did not suffer too many mechanical problems, plus it had an upgraded transmission and final drive to counter the Panther's main weakness. It was manned by a crew of 5, a driver, radio-operator, commander, gunner and a loader.

This fantastic scale radio controlled replica from Heng Long looks great and is feature packed. The highly detailed finish adds to the realism and the included commander figure completes the model perfectly. The tank fires plastic bbs and is the upgraded version with a built in real smoke generator and sound effects. Sound effects include emulation music, motor start-up, engine, machine-gun and cannonball when it fires a bb.

Requires:
8 AA Batteries for Transmitter

Specifications:
Storage Capacity: 40 BB's
Length: 60cm
Width: 19cm
Height: 17cm
Scale: 1:16
Climbing Gradient: (Changeable on different road surfaces) Apr. 35-degree

FEATURES
Built in realistic smoke generator
Highly detailed realistic model
Demonstration mode
Frequencies can be changed so multiple tanks can be used together
Super chassis, realistic suspension system, rubber covered wheels, pre-assembled tracks
A realistic commander is included
Rotating turret
Gun can be moved 30 degrees up and down
Full control of tank movement - forward, backward, rotate left and right
Many sound effects - Emulation music, motor start-up sound, Engine sound, machine-gun sound, Cannonball sound
Adjustable sound

]]>

1/16 PanzerKampfwagen RC Tank With Smoke And Sound

Fri, 29 Jan 2010 10:57:06 +0000

]]>

The Panzer III is the common name of a medium tank that was developed in the 1930s by Germany and used extensively in World War II. It weighed 23 tonnes and was fitted with a 5cm cannon as well as 2 or 3 7.92mm machine guns. The Panzer III was used in the campaigns against Poland, France, the Soviet Union and in North Africa. A handful were still in use in Normandy and at Arnhem in 1944. The Panzer III was well designed in that it had a three-man turret crew (gunner, loader and commander), leaving the commander free to concentrate on commanding the tank and maintaining situational awareness. Although other medium tanks of the time also had this feature, most tanks of the late 1930s had fewer than three men in the turret crew, potentially providing the Panzer III with a "fightability" advantage over otherwise similar tanks.

This fantastic scale radio controlled replica from Heng Long looks great and is feature packed. The highly detailed finish adds to the realism and the included commander figure completes the model perfectly. The tank fires plastic bbs and is the upgraded version with a built in real smoke generator and sound effects. Sound effects include emulation music, motor start-up, engine, machine-gun and cannonball when it fires a bb.

Requires:
8 AA Batteries for Transmitter

Specifications:
Storage Capacity: 40 BB's
Length: 36.5 cm
Width: 18.5 cm
Height: 20 cm
Scale: 1:16
Climbing Gradient: (Changeable on different road surfaces) Apr. 35-degree

]]>

1/16 Russian KV-1 Radio Controlled Tank With Smoke And Sound

Fri, 29 Jan 2010 10:45:05 +0000

]]>

The 45 tonnes Kliment Voroshilov (KV) tanks were a series of Soviet heavy tanks known for their extremely heavy armour protection, which was capable of resisting all German anti-tank weapons up to 75 mm and 88 mm caliber, both of which were comparatively rare at the time of the initial German invasion of the Soviet Union in World War II. It was equipped with a 76.2 mm model F-34 gun and four DT machine guns. The KV outweighed most other tanks of the era, being about twice as heavy as the heaviest contemporary German tanks. The KV's strengths included armor that was impenetrable by any tank-mounted weapon then in service except at point-blank range, good firepower, and good traction on soft ground.

This fantastic scale radio controlled replica from Heng Long looks great and is feature packed. The highly detailed finish adds to the realism and completes the model perfectly. The tank fires plastic bbs and is the upgraded version with a built in real smoke generator and sound effects. Sound effects include emulation music, motor start-up, engine, machine-gun and cannonball when it fires a bb.

Requires:
8 AA Batteries for Transmitter

Specifications:
Storage Capacity: 40 BB's
Length: 42.5 cm
Width: 20.6 cm
Height: 17cm
Scale: 1:16
Climbing Gradient: (Changeable on different road surfaces) Apr. 35-degree

]]>

1/16 Tauchpanzer RC Tank With Smoke And Sound

Fri, 29 Jan 2010 10:39:00 +0000

]]>

The real Panzer III Medium Tank was intended as the main German battle tank of the Second World War, capable of engaging and destroying opposing tank forces. Until then the Panzer III had been the only German designed tank armed with a gun designed to penetrate enemy armour. The Panzer III was used in the campaigns against Poland, France, the Soviet Union and in North Africa. A handful were still in use in Normandy and at Arnhem in 1944. The Tauchpanzer III was a version of the Panzer III modified to operate underwater for up to twenty minutes. The idea was for the tanks to be taken close to the British coast on specially adapted ships, and then lowered into the sea. They would then drive along the seabed before emerging on the invasion beaches.

This fantastic scale radio controlled replica from Heng Long looks great and is feature packed. The highly detailed finish adds to the realism and the included commander figure completes the model perfectly. The tank fires plastic bbs and is the upgraded version with a built in real smoke generator and sound effects. Sound effects include emulation music, motor start-up, engine, machine-gun and cannonball when it fires a bb.

Requires:
8 AA Batteries for Transmitter

Specifications:
Storage Capacity: 40 BB's
Length: 34 cm
Width: 19 cm
Height: 14 cm
Scale: 1:16
Climbing Gradient: (Changeable on different road surfaces) Apr. 35-degree

]]>

1/16 Tiger I Radio Controlled Tank With Smoke And Sound

Fri, 29 Jan 2010 10:30:46 +0000

]]>

The real Tiger I was a German heavy tank used in World War II, produced from late 1942 as an answer to the challenge of facing the unexpectedly formidable Soviet armor encountered in the initial months of Operation Barbarossa. The Tiger I design gave the Wehrmacht its first main battle tank that was capable of using its most formidable piece of ordnance, the 88 mm gun, which had previously showed its convincing effectiveness against both aircraft and other tanks. The Tiger differed from earlier German tanks principally in its design philosophy. Its predecessors balanced mobility, protection, and firepower. The Tiger I represented a new German approach that emphasised firepower and armour at the expense of mobility.

This fantastic scale radio controlled replica from Heng Long looks great and is feature packed. The highly detailed finish adds to the realism and the included commander figure completes the model perfectly. The tank fires plastic bbs and is the upgraded version with a built in real smoke generator and sound effects. Sound effects include emulation music, motor start-up, engine, machine-gun and cannonball when it fires a bb.

Requires:
8 AA Batteries for Transmitter

Specifications:
Storage Capacity: 40 BB's
Length: 52 cm
Width: 24 cm
Height: 20 cm
Scale: 1:16
Climbing Gradient: (Changeable on different road surfaces) Apr. 35-degree

]]>

1/16 Airsoft BB M26 Pershing RC Tanks

Fri, 29 Jan 2010 10:26:38 +0000

]]>

This tank is the top of the range of our RC tanks and is awesome! It is a large 1/16 scale featuring firing sounds, built-in real smoke generator, simulative motor start-up sounds, engine sounds, machine-gun sounds and cannon ball sounds.

The Snow Leopard is almost 2 feet in length! This tank is fully functional with multi-directional driving (and it's fast!), 360 degree turret swivel and the barrel raises and lowers. This tank stands out for two main reasons. Firstly it is a powerful Airsoft tank with an amazing range of almost 50 feet and a capacity of 40 pellets. It powers out plastic 6mm BB's and even has a powerful red warning light next to the barrel that illuminates just before it fires. Secondly the tank actually smokes from the exhaust. Do not confuse this with the old model which does not do this.

Have a full-on battle with up to 2 of your friends and see who will become the Airsoft Battle Tank Champion. Each Snow Leopard RC Tank can be switched between 3 different channels so the controls do not interfere with each other.

Includes:
Snow Leopard RC Tank 1/16th Scale
Transmitter
Rechargeable Battery and Charger
Realistic Commander and decals

Requires:
8 AA Batteries for Transmitter

Specifications:
Max. Firing range of motor air gun: 50 ft.
Storage Capacity: 40 BB's
22" x 13.7 " x 9"

Features:
Built in realistic smoke generator
Each tank can be changed between 3 separate frequencies so up to 3 tanks can battle at once
R/C battle tank max firing range of motor air gun appr. 50 ft. (with Hop-up System)
Automatic electric gun system installed, perfect actions radio control battle tank
Forward, reverse, regular turning, pivot turning, turret turning, recoil action and 88mm barrel moves up & down
Super chassis, realistic suspension system, rubber covered wheels, pre-assembled tracks
A realistic commander is equipped to enable this monster machine to run with full action

]]>

1/24 Airsoft BB M1A2 Battle RC Tank

Fri, 29 Jan 2010 10:20:18 +0000

]]>

This Airsoft tank is a Ready to Battle radio controlled tank meaning that it comes with everything needed to get you rolling. 1/24 scale, 3 channel remote control tank fires 6mm airsoft BB's! Full-function remote controls tank movement, turret rotation and 20 degree height, as well as firing (40 BB capacity)! The Set includes: battle tank, remote control, battery charger, Rechargeable battery included and accessories. If you have an interest in radio controlled tanks it couldn't be any easier to get started than with the M1A2.

Be a backyard armored cavalry commander with the M1A1 Abrams radio controlled tank. With its high-impact plastic construction and high-traction treads it can handle rough "battlefields" and you'll get hours of combat excitement with transmitter-controlled actions not found on other R/C tanks.

The M1A2 features super fast full multi-directional driving, turret swivel and barrel raise and lowe. For one hundred percent realism and loads of fun this tank is the perfect choice.

Performance Specifications:
Equipped with BB firing motor air gun.
Turret can turn to both sides and gun can go up and down.
All driving wheels suspension system.
2-Level Forward Speed Control.
Forward, Backward, Spin, Super Spin.
Equipped with High Gripping Caterpillar.
Tank Fighting Possible (Run up to 3 tanks at a time)
Running Time up to 60 minutes.
Length - 41cm

Package includes:
Remote control battle tank
Bag of 6mm Battle Bullet
Rechargeable Battery (For tank)
All Batteries Included
UK AC Charger/Adapter
Radio Controller
Instructions

]]>

1/30th M26 Pershing Radio Controlled Tank

Fri, 29 Jan 2010 10:15:59 +0000

]]>

The real M26 Pershing was introduced in the final stages of WWII as the successor to the M4 Sherman. Featuring a powerful 50 caliber 90mm gun with a range of 1,400m, the Pershing was designed to take on the powerful German Tiger and Panther tanks. The Pershing boasted not only assault power but also excellent mobility. Pershing tanks were also deployed to Korea at the outbreak of war in June 1950, and overwhelmed the rival T34/85 Soviet built tanks of the North Korean and Chinese armies. With the long barreled gun, heavy armor and Ford V-8 engine, this was the best American tank of WWII.

This great little scale model tank from Heng Long has been carefully designed to be an accurate replica of the original and features a lot of detail. It is a great introduction to radio controlled tanks or an excellent addition to any rc tank collection. The real working tracks and flashing gun with multiple sound effects are great fun for any tank fans.

The Pershing comes complete with a rechargeable battery pack and charger so you don't have to keep on buying batteries. The turret is fully controllable and can not only rotate but also be moved up and down.

SPECIFICATIONS
Length: 22 cm
Width: 10 cm
Height: 10 cm
Running time per charge: 20 min's
Scale: 1:30
Battery: 4.8V with charger

REQUIRES
Nothing, everything included!

FEATURES
Great detail
Very low price
Rechargeable battery pack w/ charger
Up, Down & 320 degrees turret rotation
Forward, Backward, Spin, Super Spin
Equipped with High Gripping Caterpillar
Brilliant engine sound system
Speed: 5-10 MPH

]]>

1/30th Sherman M4A3 Radio Controlled Tank

Fri, 29 Jan 2010 10:10:33 +0000

]]>

The real M4 Sherman tank was the primary tank used by the United States during World War II and it was also distributed to the Allies. In the United Kingdom the M4 was given the name Sherman after Union General William Tecumseh Sherman. and subsequently the British name found its way into common use in the US. Many nations continued to use the tank in both training and combat roles into the late 20th century. The Sherman tank was comparatively fast and maneuverable, mechanically reliable, easy to manufacture and service, and produced in many special-purpose variants, whose capabilities differed greatly. It was effective in the infantry support role. Units equipped with Shermans defeated heavier tanks by use of outflanking tactics to strike the thinner flank armor utilizing superior numbers, or by using upgunned models working with tank destroyers.

The Sherman comes complete with a rechargeable battery pack and charger so you don't have to keep on buying batteries. The turret is fully controllable and can not only rotate but also be moved up and down. The tanks come in different frequencies so that up to three tanks can be used at the same time for a big tank battle!

SPECIFICATIONS
Length: 22 cm
Width: 10 cm
Height: 10 cm
Running time per charge: 20 min's
Scale: 1:30
Battery: 4.8V with charger

REQUIRES
Nothing, everything included!

]]>

Jabo Radio Controlled Fishing Bait Boat

Fri, 29 Jan 2010 10:03:24 +0000

]]>

In the past, fishing fans cast bait in a manner of different ways which were inaccurate and usually had the disadvantage of a short casting distance. With rc bait boats, bait can be dropped exactly where you want it. These bait boats are also equipped with nice extra features to aid fishing such as a fish attracting under water light and line dropper. The deluxe version even comes with a fish finder that tells you on your LCD transmitter if there are fish under the boat! These bait boats bring a real advantage and extra fun side to fishing and just as importantly are a great excuse to have a play with a radio controlled boat while pretending to be doing something more serious!

The bait boat is made from strong plastic and is completely sealed to ensure no water can get inside, even if it turns over. If using in very wavy conditions and the boat did capsize it is designed to always go the right way up again. Another great feature of this boat is that the propellers are actually on the inside and protected. This means that even if using in weedy water the boat will never get tangled up. Other features include a fish attracting underwater lamp and a hook dropper so your hook can be dropped exactly where you want it.

The Jabo comes in two different versions with the upgraded version featuring a built in high spec fish finder. This comes with an LCD transmitter instead of the standard one that displays lots of information sent back from the boat. As well as the main fish finder function the LCD also displays water temperature, water depth, fish depth and battery life.

Specifications:
Length : 675mm
Width : 200mm
Height : 210mm
Weight: 4.25 Kg's
Battery: 12v/4.3Ah Sealed Storage
Sailing Time: 2 hours +
Speed: 1 meter / second
Range: 300m
Hopper Load: 500gs
Motors: 2 x 540

Please note colours may vary slightly from pictures.

Features:
Strong Plastic Construction
Hermetic Gum Rings Ensure Boat Is Totally Water Proof
Kent ledge Inside Cabin Keeps Boat Upright Even In Stormy Waves
Built In Propeller So Can Sail In Weedy Water Etc Without Getting Stuck
Three Range Lights For Night Sailing
3w Fish Attracting Lamp
Hook Dropping Function
High Capacity Battery

Extra Features Of B Version:
Water Depth Display to 30m
Nice LCD Transmitter
Fish Depth Display
Water Temperature Display
Battery Voltage Display
Sensitivity Adjustable

]]>

Volvo Style 1:10 Scale RC Boats

Fri, 29 Jan 2010 09:58:25 +0000

]]>

To look at and use this boat you would expect the price to be much higher. It is very quick, quicker than boats that are a lot more expensive. It also looks amazing both racing in the water and on display on it's included display stand. The model also features a great safety feature where the propeller will only turn if the boat is actually in the water. Rc boat props turn very quickly and could injure a child if they were to get hold of it while the prop was spinning but with this boat it would never happen as the prop will not turn until it is submerged in water.

The power is generated by twin racing motors and a high capacity high power 7.2v 1800mah rechargeable battery pack with UK charger. This powers the boat to speeds of 25-35km/h!

The 2ch controller has a range of about 150-200m and the boat will run for about 10 minutes of each charge.

SPECIFICATIONS
Length: 550mm
Width: 225mm
Height: 150mm
Motor: Twin
Running time: 10 min's
Battery pack: 7.2v 1800mah
Range: 150-200m

REQUIRES
8 AA Batteries for Transmitter

FEATURES
1. High speed 25-35km/h
2. Long range
3. Realistic design
4. Includes rechargeable battery pack
5. UK charger
6. Very low price
7. Twin motors
8. Safety function propellers

]]>

Heng Long Atlantic Yacht RC Boats

Fri, 29 Jan 2010 09:53:41 +0000

]]>

This is a high power low priced electric radio controlled boat from the famous manufacturer Heng Long. There are not many rc boats on the market that are as well priced as these but none at this price level that are as quick as these.

The power is generated by a size 380 racing motor and high capacity high power 8.4v 1800mah rechargeable battery pack with UK charger. This powers the boat to speeds of 25-35km/h!

The boat looks great and is fully built, ready to use out of the box. The 2ch controller has a range of about 200m and the boat will run for about 10 minutes of each charge.

SPECIFICATIONS
Length: 705mm
Width: 220mm
Height: 197mm
Motor: 380
Running time: 10 min's
Battery pack: 8.4v 1800mah
Range: 200m

REQUIRES
6 AA Batteries for Transmitter

FEATURES
1. High speed 25-35km/h
2. Long 200m range
3. Realistic design
4. Includes rechargeable battery pack
5. UK charger
6. Very low price
7. 380 type racing motor
8 . Large torsion propeller

]]>

Starmax F-5E Camo 5Ch RTF 70mm EDF Rc Jet With Retracts

Fri, 29 Jan 2010 09:48:08 +0000

]]>

The real Northrop F-5E Tiger II are part of a family of widely used light supersonic fighter aircraft, designed and built by Northrop in the United States, beginning in 1960s. Hundreds remain in service in air forces around the world. The F-5E "Tiger II" was a greatly improved version of the earlier F-5A "Freedom Fighter". Redesigned as a highly maneuverable, lightweight and inexpensive air superiority fighter, the E featured an air-to-air fire control radar system and a lead computing gun sight. More powerful J85 engines required the fuselage to be both widened and lengthened. The forward wing root was redesigned to give the "Tiger II" wing its characteristic triple delta shape.

This excellent model is based on the US Navy desert camo finish.

This F-5E is one of the highest spec and quickest jets on the market. It is a massive 1.3m in length and is fitted with a 70mm EDF. Extra power and speed is produced by the big 14.8V, 2200mah LiPo battery and 40A brushless setup. As well as extra power and speed this jet also features an automatic landing gear system and turning front wheel. To allow this the set includes a 5ch transmitter and eight servos. It's a highly maneuverable model that can easily perform inverted flight, loops and rolls etc.The model comes pre-painted with everything you need included apart from the normal AA batteries for the transmitter. The model is almost ready to fly out of the box with only very minor assembly required such as attaching the wings. Everything you need to complete is included in the box.

Included is a 5ch 1000m range transmitter, electronic speed controller, ducted fan with electric brushless motor and 8 electric servos all pre-installed. The 5ch transmitter gives full 3D control of the aileron, elevator, rudder, throttle and retracts. The 70mm ducted fan system with the brushless motors and li-po battery gives enormous power pushing the jet to crazy speeds. The high power allows full aerobatic characteristics and inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are all possible.

The attention to detail from Starmax who are the leading rc jet manufacturers gives the jet a nice realistic appearance. The jet can take off from the ground or can be hand launched. If you are not ready to be flying at high speeds then you can also fly the plane very slowly while you get used to it without any problems. The jet is made from shock resistant EPS foam with reinforced fuselage and strong wings. Should you need any spare parts though they are all available from our site. This plane is a lot of fun and you will certainly enjoy flying this fantastic model.

Specifications:
Wingspan: 760mm
Length: 1312mm
Flying Weight: 900g
Wing area: 12.44dm2
Wing Load: 72.3g/dm2
Radio System: 5Ch Tx and 6Ch Rx
Servos: 8 x 9 gram servos
Fan: 70mm Ducted fan
Motor: Powerful 2836 out runner brushless
ESC: 40A ESC 5A UBEC
Battery: 2200Mah, 14.8V
Radio Control Range: 3000 feet (1000m)

Features:
70mm EDF
Upgraded 14.8V battery
Working retracts
5 Channel Digital Proportional
Full aerobatic characteristics
Brushless setup
Ready to fly in just minutes
Super tough, lightweight airframe
Perfect appearance and emulation
Take off from ground or hand launched
Excellent flight performance
Stable inverted flight
Made by Starmax - industry leaders in quality
Slow speed flying capable
Apr. 15 min's flight time per charge

]]>

Starmax F-22 Stars Raptor 4Ch RTF Ducted Fan Rc Jet

Fri, 29 Jan 2010 09:15:12 +0000

]]>

The real Lockheed Martin/Boeing F-22 Raptor is a fighter aircraft that uses stealth technology. It is primarily an air superiority fighter, but has multiple capabilities that include ground attack, electronic warfare, and signals intelligence roles. The United States Air Force considers the F-22 a critical component of the U.S. strike force.

The F-22 is claimed by multiple sources to be the worlds most effective air superiority fighter. The US Air Force states that the F-22 cannot be matched by any known or projected fighter aircraft. Air Chief Marshal Angus Houston, Chief of the Australian Defense Force, said in 2004 that the "F-22 will be the most outstanding fighter plane ever built."

The F22 EDF Jet is one exceptional rc jet. It is power-driven by a bigger than standard 70mm electric ducted fan along with a powerful 2836 inner runner brushless motor and 45A ESC 5A UBEC. The battery has also been upgraded to a big 14.8V, 2200mah LiPo giving more power and speed. The jet is made with dense and solid foam and comes with a strong set of fixed landing gear. It flies very fast and has tremendous wing area and large control surfaces. The F22 is also very stable for intermediate pilots and very easy to fly for experts. Thrust is superb with better than 1-1 thrust to weight ratio. This jet has a 27 wingspan and is 40 in length. It flies magnificently with true aerodynamic ability and will handle wind much better just like the real F22 Raptor. It's a highly maneuverable model that can easily perform inverted flight, loops and rolls etc. The model comes pre-painted with everything you need included apart from the normal AA batteries for the transmitter. The model is almost ready to fly out of the box with only very minor assembly required such as attaching the wings. Everything you need to complete is included in the box.

Included is a 1000m range transmitter, electronic speed controller, ducted fan with electric brushless motor and 5 electric servos all pre-installed. The 4ch transmitter gives full 3D control of the aileron, elevator, rudder and throttle. The ducted fan system with the brushless motors and li-po battery gives enormous power pushing the jet to crazy speeds. The high power allows full aerobatic characteristics and inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are all possible.

Specifications:
Wingspan: 693mm
Length: 1000mm
Flying Weight: 900g
Wing area: 15dm2
Wing Load: 60g/dm2
Radio System: 4Ch Tx and 6Ch Rx
Servos: 5 x 9 gram servos
Fan: 70mm Ducted fan
Motor: Powerful 2836 out runner brushless
ESC: 45A ESC 5A UBEC
Battery: 2200Mah, 14.8V
Radio Control Range: 3000 feet (1000m)

Features:
70mm EDF
Upgraded 14.8V battery
4 Channel Digital Proportional
Full aerobatic characteristics
Brushless setup
Ready to fly in just minutes
Super tough, lightweight airframe
Perfect appearance and emulation
Take off from ground or hand launched
Excellent flight performance
Stable inverted flight
Made by Starmax - industry leaders in quality
Slow speed flying capable
Apr. 15 min's flight time per charge

]]>

Starmax F-5E Tiger 4Ch RTF Ducted Fan Rc Jet

Thu, 28 Jan 2010 16:22:40 +0000

]]>

The unique scheme used on this model is a perfect replica of the special upgraded Brazilian F-5E shown below which was designed to celebrate 30 years of service of the F-5E Tiger in the Brazilian Air Force.

1-5/8" wingspan, 34-7/8" long, 125 sq. in. wing area, 18-1/2 oz. flying weight. Tough EPO foam construction makes a more durable airframe, less prone to dings and dents. The Jet comes with all the major components pre-installed and ready for final assembly. All you need to do to complete is glue in place the vertical fin, rockets and the EPO nose cone. The 64mm fan is installed with a smooth-running out runner motor and a 30 amp speed control. The 4 servos (2-aileron, 2-elevator) are pre-installed and pre-connected to the flying surfaces. It just doesn't get much easier than this. Charge the 1300 mAh lipo battery with the included lipo balance charger, install 8-AA batteries (not included) in the transmitter and get ready to go fly fast. Flight battery access is located under the canopy, making a quick change easy to do. The jet comes with removable landing gear with a turning nose wheel. It can be flown with or without the gear. If you don't have a smooth runway, hand launching is easy to do and belly landings are a breeze. The high visibility color scheme really helps with maintaining orientation with this fast jet. Small-yes, twitchy-no; the F-5E has great speed and really grooves in the air. The jet is suitable for intermediate to advanced pilots.

Specifications:
Wingspan: 532mm
Length: 939mm
Flying Weight: 500g
Wing area: 7dm2
Wing Load: 70g/dm2
Radio System: 4Ch Tx & 6Ch Rx
Servos: 5 x 9g servos
Fan: 64MM Ducted
Motor: Powerful 14L in-runner brushless
ESC: 25A ESC
Battery: 1300Mah, 11.1V LiPo
Range: 3000 feet (1000m)

Features:
64 mm EDF
4 Channel Digital Proportional
Full aerobatic characteristics
Brushless setup
Ready to fly in just minutes
Super tough, lightweight airframe
Perfect appearance and emulation
Take off from ground or hand launched
Excellent flight performance
Stable inverted flight
Made by Starmax - industry leaders in quality
Slow speed flying capable
Apr. 15 min's flight time per charge

]]>

F-16 Fighting Falcon 4Ch RTF Ducted Fan Rc Jet

Thu, 28 Jan 2010 16:17:18 +0000

]]>

The Lockheed Martin F-16 Fighting Falcon is a multi role jet fighter aircraft originally developed by General Dynamics for the United States Air Force. Designed as a lightweight fighter, it evolved into a successful multi role aircraft. The Falcon's versatility is a paramount reason it has proven a success on the export market, having been selected to serve in the air forces of 25 nations. The Fighting Falcon is a dog fighter with numerous innovations including a frameless, bubble canopy for better visibility, side-mounted control stick to ease control while under high g-forces, and reclined seat to reduce the effect of g-forces on the pilot. Weapons include a M61 Vulcan cannon and various missiles mounted on up to 11 hard points. It was also the first fighter aircraft deliberately built to sustain 9-g turns. It has a thrust-to-weight ratio greater than one, providing enough power to climb and accelerate vertically. Although the F-16's official name is "Fighting Falcon", it is known to its pilots as the "Viper", due to it resembling a cobra snake and after the Battlestar Galactica starfighter.

This is an excellent scale model aimed at intermediate to advanced fliers. It is our quickest jet and can fly at over 90mph! It is a highly manoeuvrable model that can easily perform inverted flight, loops and rolls etc. It comes pre-painted with everything you need included apart from the normal AA batteries for the transmitter. The model is almost ready to fly out of the box with only very minor assembly required such as attaching the wings. Everything you need to complete is included in the box.

Included is a 2.4Ghz 1000m range transmitter, electronic speed controller, ducted fan with electric brushless motor and 5 electric servos all pre-installed. The 4ch transmitter gives full 3D control of the aileron, elevator, rudder and throttle. The ducted fan system with the brushless motors and li-po battery gives enormous power pushing the jet to speeds of 90 mph. The high power allows full aerobatic characteristics and inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are all possible.

The attention to detail gives the jet a nice realistic appearance and the plane even features a turning front wheel. The jet can take off from the ground or can be hand launched. If you are not ready to be flying at 90mph then you can also fly the plane very slowly while you get used to it without any problems. The jet is made from shock resistant EPS foam with reinforced fuselage and strong wings. Should you need any spare parts though they are all available from our site. This plane is a lot of fun and you will certainly enjoy flying this fantastic model.

Specifications:
Wingspan: 780mm
Overall Length: 1230mm
Flying Weight: 1000g
Drive System: 70mm ducted fan
Servo: 5X 9g high speed micro servos
ESC: 45A Brushless speed controller
Battery: 14.8V 2200mAh Li-Polymer
Control system: 4 CH 2.4Ghz Radio Transmitter and 6 CH Micro Receiver
Radio Control Range: 3000 feet (1000m)

Features:
4 Channel Digital Proportional
2.4G Radio System
Full aerobatic characteristics
Flying speed of 90mph
Brushless setup
Turning front-wheel
Ready to fly in just minutes
Super tough, lightweight airframe
Perfect appearance and emulation
Take off from ground or hand launched
Excellent flight performance
Stable inverted flight
One of the best looking jets in the market
Slow speed flying capable
Apr. 10 min's flight time per charge

]]>

Freewing F-15 Strike Eagle 4ch RC Jet RTF

Thu, 28 Jan 2010 16:10:45 +0000

]]>

This real F-15 Eagle that this model is based on is a twin-engine, all-weather tactical fighter designed to gain and maintain air superiority in aerial combat. It was developed for the United States Air Force, and first flew in July 1972. It is one of the most recognized fighters of the modern day. The F-15E Strike Eagle derivative is an all-weather strike fighter that entered service in 1989. The U.S. Air Force plans to keep the F-15 in service until 2025. The paint scheme used is of the F-15 Aggressors from the 65th Aggressor Squadron at Nellis Air Force Base.

This is an excellent scale model aimed at intermediate to advanced fliers. It is a highly manoeuvrable model that can easily perform inverted flight, loops and rolls etc. It comes pre-painted with everything you need included apart from the normal AA batteries for the transmitter. The model is almost ready to fly out of the box with only very minor assembly required such as attaching the wings. Everything you need to complete is included in the box.

Includes is a 1000m range transmitter, electronic speed controller, ducted fan with electric brushless motor and 5 electric servos all pre-installed. The 4ch transmitter gives full 3D control of the aileron, elevator, rudder and throttle. The ducted fan system with the brushless motors and li-po battery gives enormous power pushing the jet to speeds of 70 mph. The high power allows full aerobatic characteristics and inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are all possible.

The attention to detail gives the jet a nice realistic appearance and the plane even features a turning front wheel. The jet can take off from the ground or can be hand launched. If you are not ready to be flying at 70mph then you can also fly the plane very slowly while you get used to it without any problems. The jet is made from shock resistant EPS foam with reinforced fuselage and strong wings. Should you need any spare parts though they are all available from our site. This plane is a lot of fun and you will certainly enjoy flying this fantastic model.

Specifications:
Wingspan: 741mm
Overall Length: 1100mm
Flying Weight: 680g
Drive System: 4300KV In-runner Brushless motor
Servo: 5X 9g high speed micro servos
ESC: 30A Brushless speed controller
Battery: 11.1V 2200mAh Li-Polymer
Control system: 4 CH Multifunctional FM Radio Transmitter and 6 CH Micro Receiver
Radio Control Range: 3000 feet (1000m)

Features:
4 Channel Digital Proportional
Full aerobatic characteristics
Flying speed of 70mph
Brushless setup
Turning front-wheel
Ready to fly in just minutes
Super tough, lightweight airframe
Perfect appearance and emulation
Take off from ground or hand launched
Excellent flight performance
Stable inverted flight
One of the best looking jets in the market
Slow speed flying capable
Apr. 15 min's flight time per charge

]]>

Rafale Combat Fighter 4Ch RTF Ducted Fan Rc Jet

Thu, 28 Jan 2010 16:06:52 +0000

]]>

The Rafale was developed by Dassault-Breguet for the Armée de l'Air. The Dassault Rafale, when released into operational service in the late 1990's, was the pinnacle of French aircraft engineering. The system incorporated the latest in fly-by-wire technology, composite materials and aerodynamic design to compliment the broad array of roles required of any fighter in any military force.

The Dassault Rafale was already on the drawing boards even as the Dassault Mirage 2000 was being designed and produced. With France initially a part of the Eurofighter Typhoon conglomeration, the Rafale development was put into high gear when France withdrew from the program. The Rafale would become possibly the best Dassault fighter ever produced and step forward as the next generation in French aircraft design.

Based on its full-scale counterpart, this French jet flight model has a high roll rate and even can do the famous "cobra maneuver" flight. This is an excellent scale model aimed at intermediate to advanced fliers. It is a highly manoeuvrable model that can easily perform inverted flight, loops and rolls etc. It comes pre-painted with everything you need included apart from the normal AA batteries for the transmitter. The model is almost ready to fly out of the box with only very minor assembly required such as attaching the wings. Everything you need to complete is included in the box.

Included is a 2.4Ghz 1000m range transmitter, electronic speed controller, ducted fan with electric brushless motor and 3 electric servos all pre-installed. The 4ch transmitter gives full 3D control of the aileron, elevator, rudder and throttle. The ducted fan system with the brushless motors and li-po battery gives enormous power pushing the jet to speeds of 70 mph. The high power allows full aerobatic characteristics and inside loops, outside loops, axial rolls, inverted flight, knife edge, stall turns, hammerheads, and spins are all possible.

The attention to detail gives the jet a nice realistic appearance. The jet can take off from the ground or can be hand launched. If you are not ready to be flying at 70mph then you can also fly the plane very slowly while you get used to it without any problems. The jet is made from shock resistant EPS foam with reinforced fuselage and strong wings. Should you need any spare parts though they are all available from our site. This plane is a lot of fun and you will certainly enjoy flying this fantastic model.

Specifications:
Wingspan: 660mm
Overall Length: 1000mm
Flying Weight: 610g
Height: 305mm
Wing Area: 5dm²
Drive System: Ducted Fan
Motor: Inrunner Brushless
Servo: 3 X 9g high speed micro servos
Speed Controller: 30 Amp Brushless
Battery: 11.1V 1300mah Li-Polymer
Control system: 4 CH 2.4Ghz Radio Transmitter and Micro Receiver

Features:
4 Channel Digital Proportional
Upgraded 2.4G Radio System
Full aerobatic characteristics
Flying speed of 70mph
Brushless setup
Turning front-wheel
Ready to fly in just minutes
Super tough, lightweight airframe
Perfect appearance and emulation
Take off from ground or hand launched
Excellent flight performance
Stable inverted flight
One of the best looking jets in the market
Slow speed flying capable
Apr. 10 min's flight time per charge
High roll rate

]]>

Thunderbird 3Ch RC Glider

Thu, 28 Jan 2010 16:02:29 +0000

]]>

This great RC aircraft comes with absolutely everything you need to fly - a total complete package that includes a 4Ch Radio Transmitter and receiver. Although the model is a 3ch model a great feature is that the radio equipment is 4Ch which means you can use it with more advanced 4ch RC Aircraft in the future.

The glider is designed to achieve perfect balance. You'll have complete control over every twist and turns - absolutely full aerial maneuverability. Let your imagination soar in the sky! You can launch this plane almost anywhere you want.

The Thunderbird has a minimal number of parts - unlike many other plane's designs. This means when you crash, everyone does, there are fewer parts to break. The body is very durable and almost indestructible. The rotors are efficient, safe, and are inexpensive to replace.

Specs:
Battery Operated 380 Motor RC Aircraft
Ready to Fly, assembly can be done in 10 mins.
Slow Speed Flying Capable
Shock Resistant ABS Plastic Fuselage and Strong Wings
2 X 17g micro servo for Rudder and Elevator Control
R/C Set included, Complete 3 Channel Radio Control
Complete Left/Right Control by Rudder
Complete Pitch Control by Elevator
Powered by 8.4V 600MAH NIMH re-chargeable battery (UK Charger included)
Can Fly as a Glider (without Motor Power)

Dimensions:
Wingspan: 1100MM
Length: 820MM
Weight: 500g
Battery: Ni-Mh 8.4V/600MAH
Power System: 380 MOTOR
Controller: 4 channel RC Tx/Rx and 2 mini servo and 1 electronic speed controller
Battery Requirements: 8X AA for the transmitter (not included)

]]>

Art-Tech QQ-Dragon 2ch RC Plane

Thu, 28 Jan 2010 15:58:58 +0000

]]>

If you have never flown an RC plane before and don't want to risk damaging a model while learning then this is the perfect model for you. This plane is tough and very easy to fly. Manufactured by Art-Tech who are one of the best quality RC plane manufacturers in the world, this plane stands out from the crowd.

The plane is a ready-to-fly plane out of the box with a very quick charge time. It is the perfect choice for beginners but also for intermediates who just want a bit of fun without breaking the bank. There are a few similar entry level planes on the market but we found this one was the best. One of the main reasons is the way the controller works. Usually with entry level RC planes the left stick on the transmitter controls the left motor and the right stick controls the right motor. This makes flying unrealistic and awkward. With the QQ-Dragon the controls are like a full scale plane. The left stick controls the throttle and the right stick is for turning.

As the plane is made by Art-Tech you can be assured of the reliability and attention to detail. The plane has a rubber nose to protect it from crash landings and has a quick charging slot that you plug the transmitter into to charge it without taking the battery pack out. Everything you need is there including some spare blades, screw driver, display stand and 4.8v battery pack. The only thing needed is 8 normal AA batteries for the transmitter.

Specs
Wingspan: 400mm
Length: 330mm
Weight: 52g
Transmitter: 2 Ch
Battery: 4.8v 150mah
Flight time: 10-15 mins

Features
1. Very easy to fly for beginners
2. Can fly in small places & indoors
3. Stable flightv 4. Light so wont brake anything
5. Crash resistant with rubber nose
6. Simple radio control
7. Very low price
8. Ready to fly out of the box
9. Comes with spare blades
10. Quick 8 minute charge feature
11. Long 100m range

]]>

Large Scale RC Helicopter With Wireless Video Camera & Receiver

Thu, 28 Jan 2010 15:47:05 +0000

]]>

This is the worlds first dual rotor radio controlled helicopter with wireless video camera function! This is a large scale helicopter that is bigger than others on the market which makes it a lot more stable for outdoor flight. It is also a dual rotor helicopter which makes flying much easier and along with the large size makes it one of the most stable helicopters in the world. The helicopter needs to be this stable as housed inside is a wireless video camera which transmits a video feed back to a receiver that can be connected to a USB port on a computer to view what the helicopter is seeing. This radio controlled helicopter could be flown from viewing the video feed without even having to watch the helicopter! The camera gets it's power from the helicopter battery so does not need a separate power source.

The helicopter is a classic helicopter with lovely canopy and scale appearance. It is a scale model of the Hughes/MD 500 light utility helicopter.

The spycopter comes with a 4ch transmitter featuring the new 2.4GHz technology. 2.4GHz systems offer many benefits over traditional radio systems such as elimination of interference, automatic and unique selection of free frequency and faster response times.

Specs:
1. Main Rotor Diameter: 450mm
2. Length: 450 mm
3. Height: 250 mm
4. Flying Weight: 350g
5. Driven system: 2 x 370 motors
6. Servo: 2 x 9g servos
7. Battery: 7.4V 1000mAh Li-polymer
8. Control system: 4CH 2.4GHz Transmitter and 4-in-1 Receiver
9. Radio Control Range: 2500+ feet

Features:
1. Large stable radio controlled helicopter
2. 2.4GHz radio
3. Built in video camera
4. USB receiver
5. Li-po battery power
6. Twin blade stable flight
7. Indoor or outdoor flight
8. Ideal model for beginner
9. Li-po Balance charger
10. Flying time: 8-10 mins
11. Realistic canopy

]]>

CopterX CX450BA Black Angel RC Helicopter

Thu, 28 Jan 2010 15:40:26 +0000

]]>

Black Angel is one of the most advance 450 size 3D helicopters on the market. With its innovative design and robust aluminium and carbon construction, Black Angel is able to offer performance rivals can only dream of. The Black Angel is a completely new helicopter designed from the ground up. A lot of unique features are brand new or only available for larger helicopters. Things like +/- 15 degree patch range; carbon main and tail blade; carbon fly paddle; one piece carbon fiber main frame; CNC main rotor and tail drive assembly; oversized bearing and feathering shaft; pre painted fiber glass streamline canopy, etc. With its wide range of adjustability you will be able to take the hobby to the highest level.

FEATURE SUMMARY
+/- 15 extra wide pitch range.
Over sized feathering shaft, screws, blade grip bearing etc. for low maintenance.
4mm feathering shaft with thrusted bearing for accurate high load 3D operation.
Hardened aluminum washout base & rudder slider is long lasting & light weight.
240 reinforced swash plate for positive response
One piece CCPM swash plate design for durability
Simple head design for quick output and easy maintenance
Fully ball raced to handle head speed of 3500rpm+ & tail speed of 13600rpm+
Extra wide drive belt for trouble free and quick operation
Direct tail drive system weight saving and quicker response
Extra wide drive belt to ensure non slip and sensitive rudder control
High strength nylon main gear for quite and smooth operation
Precise high wear resistance aluminum alloy pulley set
One piece carbon fiber main frame for strength and durability
Light weight carbon bottom plate, ESC mount, battery mount & anti rotation bracket.
High strength aluminum alloy tail boom look
Aluminum alloy rudder servo mount
Light weight one piece composite landing skid
Plastic Canopy mounts to isolate canopy vibration
Light weight high strength glass fiber per painted canopy

No need to ever spend money upgrading the Black Angel as all upgrades come as standard with full CNC aluminum or carbon throughout. All parts are ball raced & aluminum parts were finished with a beautiful anodized grey. The carbon blades are top of the line products & can really perform during heavy load conditions. A lot of parts on the rotor head are over sized or hardened. 4mm feathering shaft, hardened aluminum alloy washout, oversize main shaft lock collar, one piece swashplate, etc. All these allow high loading for extreme 3D maneuvers.

The tail drive system also features a light weight but rigid CNC & carbon construction including carbon tail blades. The extra wide long life drive belt ensures positive rudder control during 3D maneuvers and belt tensioners on both ends reduce the chance of skipping and derailing. A one piece carbon frame reduces the number of aluminum parts necessary for the frame resulting in a light weight and rigid construction. All mounts are aluminum including a special composite canopy mount to reduce vibration.

Specifications:
Length: 653mm
Height: 240mm
Main Rotor: 714mm
Tail Rotor: 157mm
Motor Gear: 12T/13T
Main Gear: 150T
Autorotation Tail Drive Gear: 43T
Tail Drive Gear: 10T
Drive Gear Ratio: 1:12.5:4.3(12T) / 1:11.54:4.3(13T)
Weight(without electric parts): 370g
Weight(including electric parts): 760~800g

Features Include:
CNC & Carbon Construction
Auto-Rotation System
Rear Tail Servo Mount
Collective Pitch System
Tail Rotor Drive Belt System
Main Drive Gear with Cooling Fan
Professional Servo Control Lever Design

Package Contents:
Please note the Black Angel is available in either KIT form or RTF. The RTF version will still require some setup but everything is included and it comes pre-built. The KIT version does not include any electronics and requires some assembly.

KIT
CopterX CX450 Black Angel Kit x 1

RTF
CopterX CX450 Black Angel Kit x 1
CopterX 3500Kv Brushless Motor x 1
CopterX 50A ESC x 1
CopterX 2.4G Transmitter & Receiver x 1
CopterX 9g Servos x 3
Fusonic High Speed Digital Servo x 1
CopterX Gyro 240 x 1
Full Size Aluminum Case x 1
CopterX UK Balance Charger x 1
Switching Adapter x 1
CopterX Li-Polymer Battery 11.1V 15C 2200mAh x 1

]]>

CopterX CX450SE V2 Rc Helicopter

Thu, 28 Jan 2010 15:31:06 +0000

]]>

The CopterX CX 450 V2 Superior Edition (eCCPM) represents the state of the art in micro helicopter technology by utilising the latest design techniques and highest quality aluminium and carbon materials. The aluminum parts are anodized in a fantastic looking blue color which really stand out against the high gloss carbon frame. This kit is for the flyers who want uncompromised performance and quality to take the hobby to the highest level.

FEATURE SUMMARY

New CNC carbon frame improves the rigidity and is perfect for 3D flying.

CCPM collective pitch version with new aluminum parts for prompt, precision action.

SSG battery mounting plate connects to main frame. It makes the center of gravity closer to the rotor blades reducing the correction needed after 3D maneuvers.

Rigid CNC aluminum rotor head for precise and smooth movements.

Uses Ball and Hiller two system mixing control.

CCPM control can simultaneously control 3 servos for AILE, EVLE & PIT actions. This CCPM control system is great for 3D flying control and extending the life cycle of servos.

New streamlined carbon tail rotor blades makes the gyro more efficient.

New tail rotor control set, CNC control piece and movable ball link for smooth pitch travel.

Adjustable flybar weight - When normal flying you can add the weights to the flybar paddles for stable flight. When aerobatic flying you can remove the weights for added flexibility.

CNC Metal tail unit and tail holder use high rigid aluminum.

New gear ratio(4.24:1), suitable for the higher KV motor.

Uses aluminum alloy drive pulley and tail drive pulley for high rigidity and wear resistance. It is efficient to reduce the rotation loss and makes it smoother.

Stainless steel anti-oxidization linkage balls are used throughout and are wear resistant

Tail rotor hub is made of stainless steel and is very rigid.

Great stable and sensitive mixing lever design. Gives high stability and precision for 3D flight.

CX 450SE special adjustable pitch system, hold rotation system and tail rotor drive belt system makes this a fantastic and original helicopter.

The CX450 SE is one of the top spec helicopters on the market. No need to ever spend money on upgrades as the SE has them all prefitted. To buy a standard helicopter and then upgrade it to this level would cost many times more. With full CNC aluminum or carbon throughout the CX450SE is a tough and higly capable model for extreme flying. All parts are ball raced & a lot of parts on the rotor head are over sized or hardened. Not only are the materials high spec but so is the technology making this an amazing package.

CCPM, anti rotation, dual cooling fan, adjustable throughout etc., this helicopter has it all. The tail drive system also features a light weight but rigid CNC & carbon construction. The extra wide long life drive belt ensures positive rudder control during 3D maneuvers and belt tensioners on both ends reduce the chance of skipping and derailing. The carbon frame is light weight and rigid. All mounts are aluminum including a special composite canopy mount to reduce vibration.

Specifications:
Length:650mm
Height:230mm
Main Rotor:700mm
Tail Rotor:150mm
Motor Gear:13T/11T
Main Gear:150T
Autorotation Tail Drive Gear:106T
Tail Drive Gear:25T
Drive Gear Ratio:1:11.5:4.24/1:13.6:4.24
Weight(without power system):354g
Weight(including power system):690g

Package Contents:
Please note the CopterX 450SE V2 is available in either KIT form or RTF. The RTF version will still require some setup but everything is included and it comes pre-built. The KIT version does not include any electronics and requires some assembly.

KIT
CopterX CX 450SE V2 Kit x 1

RTF
CopterX CX 450SE V2 x 1
CopterX 3500Kv Brushless Motor x 1
CopterX 50A ESC x 1
CopterX 2.4G Transmitter & Receiver x 1
CopterX 9g Servos x 4
CopterX Gyro 240 x 1
Full Size Aluminum Case x 1
CopterX Balance UK Charger x 1
UK Switching Adapter x 1
CopterX Li-Polymer Battery 11.1V 15C 2200mAh x 1

]]>

CopterX CX450ME V2 Rc Helicopter

Thu, 28 Jan 2010 15:13:58 +0000

]]>

The CopterX CX 450 V2 ME (eCCPM) represents the state of the art in micro helicopter technology by utilising the latest design techniques and highest quality materials. This kit is for the flyers who want uncompromised performance and quality to take the hobby to the highest level. The ME version is perfect for people who want a proper 450 helicopter with all the features of the more expensive SE and BA versions but with a lower initial outlay. The ME achieves this by keeping all the technology and layout the same but swaps some of the expensive carbon and aluminium parts for aluminium and plastic.

FEATURE SUMMARY

The Aluminum frame improves the rigidity and is perfect for 3D flying.
SSG battery mounting plate connects to the main frame. It makes the center of gravity closer to the rotor blades and reduces the correction needed when rolling.
High quality designed rotor head set provides smooth movements.
Uses Ball and Hiller two system mixing control. Through the simple structure of the Ball control system, power-saving of the Hiller system and the CCPM control you can simultaneously control 3 servos for AILE, EVLE, PIT 3 actions. This CCPM control system is great for 3D flying control and extending the life cycle of servos.
New streamlined skeleton makes the gyro more efficient.
New tail rotor control set, control piece and movable ball link for smooth pitch travel.
Adjustable flybar weight - When normal flying you can add the weights on the flybar paddles for stable flight. When aerobatic flying remove the flybar weight for the flexibility of 3D actions.
New gear ratio (4.24:1) is suitable for the high KV brushless motor and provides more safety and reliability.
All the kit uses stainless steel linkage balls for wear resistance and anti-oxidization.
Great stable and sensitive mixing lever design gives great stability and precision for 3D flight.
CX 450ME special adjustable pitch system, hold rotation system and tail rotor drive belt system making this an original and ground breaking helicopter.

The CX450 is one of the top spec helicopters on the market for people who want to take the hobby to the highest level. What's great about the ME version is that although to keep the costs down some of the carbon/aluminium parts have been replaced with aluminium & plastic, they are all the same shape so can be upgraded at any time. If you do not want the initial bigger outlay of the SE or BA versions then you can still get this version with all the same technology and if you decide to later can upgrade it at your own pace.

CCPM, anti rotation, dual cooling fan, adjustable throughout etc., this helicopter has it all. The tail drive system also features a light weight but rigid construction. The extra wide long life drive belt ensures positive rudder control during 3D maneuvers and belt tensioners on both ends reduce the chance of skipping and derailing. The aluminium frame is light weight and rigid. The ME version represents real value for money and you will not find another 450 scale helicopter with these features at this low price.

Specifications:
Length:650mm
Height:230mm
Main Rotor:700mm
Tail Rotor:150mm
Motor Gear:13T/11T
Main Gear:150T
Autorotation Tail Drive Gear:106T
Tail Drive Gear:25Tv Drive Gear Ratio:1:11.5:4.24/1:13.6:4.24
Weight(without power system):254g
Weight(including power system):590g

Features Include:
Aluminium frame and tail boom
Auto-Rotation System
Rear Tail Servo Mount
Collective Pitch System
Tail Rotor Drive Belt System
Main Drive Gear with Cooling Fan
Professional Servo Control Lever Design

Package Contents:
Please note the CopterX 450ME V2 is available in either KIT form or RTF. The RTF version will still require some setup but everything is included and it comes pre-built. The KIT version does not include any electronics and requires some assembly.

KIT
CopterX CX 450ME V2 Kit x 1

RTF
CopterX CX 450ME V2 x 1
CopterX 3500Kv Brushless Motor x 1
CopterX 50A ESC x 1
CopterX 2.4G Transmitter & Receiver x 1
CopterX 9g Servos x 4
CopterX Gyro 240 x 1
Full Size Aluminum Case x 1
CopterX Balance UK Charger x 1
UK Switching Adapter x 1
CopterX Li-Polymer Battery 11.1V 15C 2200mAh x 1

]]>

Esky Belt CP V2 Rc Helicopter

Thu, 28 Jan 2010 15:01:48 +0000

]]>

Everything about the helicopter has been designed for precise extreme flying. Massive power is provided from the 450 brushless motor and whopping 1800mAh Li-Polymer battery allowing this helicopter to do things that others would simply can't. The Belt CP V2 comes fully built with radio equipment included and also features Esky's new head lock gyro that aids in sport flying and aerobatics. The construction and design is high quality with alloy parts used where needed.

The Belt CP V2 uses a belt driven tail rotor which is superior to the separate tail motor system used on entry level models. The helicopter has also been made stronger with a steel fly bar, main shaft and tail shaft along with a strong tail stand and shock proof iron landing skids. Ball bearings are used throughout instead of the normal metal bearings and a high inertial main blade is used to create even more lift. The included radio system is Esky's latest feature packed high quality 6ch transmitter with digital servos used in the helicopter for more precise control.

Specifications:
Length: 640mm
Height: 230mm
Main Blade diameter: 680mm
Tail Blades diameter: 130mm
Motor gear: 10T
Main driven gear: 140T
Tail driven gear: 110T
Driven gear rate: 14:1:5
Motor: 450 brushless motor
ESC: 25A
Gyro: New Esky headlock gyro
Servo: Digital *4Pcs
Transmitter: 6 channel 2.4G or 35Mhz
Receiver: 6 channel
Battery: Li-polymer 1800mAh, 11.1V, 20C discharge

Features:
1. Completely assembled and tested at the factory.
2. 120 degree ECCPM control system.
3. New high-tech 6-channel RC system with choice of 2.4G or 35Mhz
4. High performance head lock gyro is capable of sport flying and 3D aerobatics.
5. Digital sub-micro servos and micro head lock gyro offer precise and powerful control.
6. Stainless steel fly bar, main shaft and tail shaft.
7. 450 brushless motor, 25A brushless ESC and 3S 11.1V 1800mAh 20C Li-Po battery deliver incredible power and performance.
8. Auto-rotation system
9. Belt drive system
10. High inertial main blade
11. Shock proof iron landing skids
12. Full ball bearings and metal ball ends
13. Strong carbon fibre tail stand

]]>

Esky Belt-CP 6ch Brushless RC Helicopter

Thu, 28 Jan 2010 14:56:41 +0000

]]>

The Belt-CP is the newest single blade acrobatic helicopter from the best RC helicopter manufacturer ESky. The helicopter has several performance enhancements but the massive upgrade is the brushless motor system. The brushless setup allows the Belt-CP to out-perform any other normal motor RC helicopter on the market.

The brushless motor and brushless motor ESC offers several advantages over normal DC motors, including higher efficiency and reliability, reduced noise, longer lifetime (no brush erosion), elimination of ionizing sparks from the commutator, and overall reduction of interference. The maximum power that can be applied to a brushless motor is exceptionally high, limited almost exclusively by heat. This makes the model extremely powerful but still higly agile as you do not need to use a big heavy normal motor.

New 6 channel Transmitter with PIT and PLT mode lock switch and adjustable dial.

As well as the brushless setup the Belt-CP still boasts all the features and more that you would expect from a helicopter at this level. Belt driven tail rotor, alloy tail boom, carbon fibre tail stand, top of the range gyro and high power lithium battery, this RC helicopter ticks all the boxes.

Specs:
(1).Length:650mm
(2).Height:230mm
(3).Main Blade diameter:680mm
(4).Tail Blades diameter :130mm
(5).Motor gear:10T
(6).Main driven gear:140T
(7).Tail driven gear:110T
(8).Driven gear rate:10:140/110:22
(9).weight:About 670g(Including 1800mAh,11.1V li-poly Battery)

Features:
(1).CCPM System
(2).Auto-rotation Stystem
(3).Tail rotor Belt Drive System
(4).High Inertial Main Blade
(5).High Rigidity Iron Main Shaft
(6).Shock Proof Iron Landing Skids
(7).Full Ball Bearing & Metal Ball End
(8).High rigidity alloy tail boom
(9).High Strength Carbon Fibre Tail Stand

]]>

ESky King 3 - 6Ch Brushless RC Helicopter

Thu, 28 Jan 2010 14:42:55 +0000

]]>

The King 3 is brand new to the market and is a top of the range remote controlled helicopter from Esky. It is a big 400 size helicopter aimed at intermediate to advanced pilots. This high spec model is one of the most advanced we sell not to mention one of the best quality electric helicopters on the market. The King 3 version is the replacement to the King 2 which is Esky's top of the range belt driven helicopter. It is the step up from the Honey Bee CP2 and is feature packed for extreme stunts and tricks. If you have had a 4ch or 6ch radio controlled helicopter before and want to take the hobby to the next level then this model can go all the way.

The main differences between a standard 6ch heli and this are:

1. Belt driven tail - Unlike the CP2 which has a separate motor on the tail this has a new belt driven tail system for precise aerobatic actions and more reliable performance. The tail system has a slipper clutch to help avoid damage if you crash it.

2. Sturdier construction - The King features a metal tail boom, strong fins and bulkier parts all round.

3. Brushless motor - This powerful large current motor gives enough torque to pull off the most demanding stunts.

4. Separate gyro etc - Most helicopters have an all in one mixer, receiver, speed controller and gyro. This is great for a simple radio controlled helicopter but for a stunt helicopter like this an all in one unit would not be enough. The King therefore comes with separate high quality receiver/mixer, speed controller and Gyro making it highly adjustable and reliable.

5. Upgradeable - The King features upgradeable parts which are available from our upgrade section. The model can be kited out with metal parts and you can even swap the standard cabin for a highly detailed scale cabin for ultimate realism.

6. New 6 channel Transmitter with PIT and PLT mode lock switch and adjustable dial. You can choose between the Mhz version with changeable frequency crystals or the 2.4 Ghz version which does not require different crystals to be used with other models in the same area.

King 2 to King 3

This all new King 3 version has some major improvements over the old King 2:

1. New brushless motor and ESC for more power
2. Esky's all new head lock gyro for sport flying and 3D acrobatics
3. Digital servos
4. Upgraded battery from 1000mah to 1500mah
5. New high-tech radio system
6. Improved main frame
These upgrades all work together to give the King 3 increased stability, power and accuracy as well as giving more direct control to the pilot.

Specifications:
Length: 550mm
Height: 200mm
Main Blade diameter: 600mm
Tail Blades diameter: 130mm
Motor gear: 10T
Main driven gear: 140T
Gear rate: 14:1:4.44
Weight: About 390g
Motor: 400 brushless motor
ESC: 25A EK1-0350
Gyro: Esky professional Head Lock Gyro EK2-0704B
Servo: 7.5g Digital servos*4Pcs
Transmitter: 6-channel 2.4G or 35Mhz
Receiver: 6-channel
Battery: Li-polymer 1500mAh, 11.1V

Features:
1. Completely assembled and tested at the factory.
2. 120 degree ECCPM control system.
3. New High-tech 6-channel RC system.
4. High performance Heading Lock gyro is Capable of sport flying and 3D aerobatics.
5. Digital Sub-Micro servos and Micro Heading Lock gyro offer precise and powerful control.
6. Stainless steel fly bar, main shaft and tail shaft.
7. 400 brushless motor, 25A brushless ESC and 3S 11.1V 1500mAh 20C Li-Po battery deliver incredible power and performance.
8. Auto-rotation system.
9. Belt Drive System.
10. High Inertial Main Blade.
11. High Rigidity Iron Main Shaft.
12. Full Ball Bearing & Metal Ball End.
13. High rigidity alloy tail boom.
14. High Strength Tail Stand.

]]>

Esky Honey Bee CP3 6ch Rc Helicopter - 2.4G Version

Thu, 28 Jan 2010 14:31:29 +0000

]]>

The Honey Bee CP3 rc helicopter is the latest 6 channel aerobatic helicopter with collective pitch. Not to be confused with the normal radio controlled helicopters that are on the market, this is an advanced model with wooden blades and more stable flight giving the ability to fly upside down and perform advanced stunts both indoors and outdoors. If you are looking for a helicopter that can do more than the standard movements and want to try something that can fly at high speeds and perform stunts then this is the helicopter to go for.

The CP3 replaces the old CP2 and has been upgraded and improved in many ways. As well as looking better the helicopter has been made much stronger with thicker and stronger parts used throughout including much thicker landing skids to protect it from heavy landings. The electronics have also been upgraded with digital servos and new motor.

The transmitter and receiver have been upgraded to the new 2.4Ghz technology. 2.4Ghz is more reliable and allows many models to be used at the same time without having to change crystals like with the older mhz versions.

Specifications:
Length: 525mm
Height: 185mm
Main rotor diameter: 540mm
Tail rotor diameter : 800mm
Motor gear: 8T
Weight: 410g
Battery: 11.1V 1000mAh Li-po with UK Charger
Motor: Super370 motor + CN12 motor
Transmitter: 2.4GHz 6CH
Receiver: 2.4GHz 6CH
3in1 controller: Gyro, mixer, ESC
Servos: Digital 7.5g, 1.0kg/cm, 0.1s/60°

Features:
1. CCPM system allows more aerobatic actions and tricks.
2. Symmetrical stronger wooden airfoil has better aerobatic characteristics.
3. Powerful motor allows indoor and outdoor use.
4 . 370 super motor provides super power for high performance flight.
5. Simple mechanical structure design, easy maintenance.
6 . Durable Material, capable of bearing most crashes without any damage.
7 . High performance main rotor blade significantly increase the strength for performing advanced 3D maneuvers.
8 . Adjustable Pitch Control System, stainless steel Fly Bar.
9 . Fully assembled and tested in the factory.
10 . New high-tech 6-channel 2.4G rc system.
11. Digital sub-micro servos offer precise and powerful control.

]]>

Esky Honey Bee V2 4ch Rc Helicopter - 2.4G Version

Thu, 28 Jan 2010 14:24:36 +0000

]]>

The Honey Bee V2 is the latest version of this worldwide famous beginners helicopter. If you want to learn how to fly a proper single blade helicopter then this is the best choice. The Esky Honey Bee Series of rc helicopters feature good performance for superior strength, stability, controllable flight and durability. Honey Bee helicopters are designed with beginners in mind and are completely assembled in the factory. You can be enjoying flying your helicopter within minutes of opening the box.

The Honey Bee 2 replaces the old Honey Bee 1 and has been upgraded and improved in many ways. As well as looking better the helicopter has been made much stronger with thicker and stronger parts used throughout including much thicker landing skids to protect it from heavy landings. The electronics have also been upgraded with digital servos and new motor.

Specifications:
Length: 510mm
Height: 165mm
Main rotor diameter: 510mm
Weight: 304g
Battery: 11.1V 800mAh Li-po with UK Charger
Motor: 370 motor + CN12 motor
Transmitter: 2.4GHz 4CH
Receiver: 2.4GHz 4CH
3in1 controller: Gyro, mixer, ESC
Servos: Digital 7.5g, 1.0kg/cm, 0.1s/60°

Features:
1. Best model to learn to fly a single blade helicopter.
2 . 370 motor provides good power.
3. Simple mechanical structure design, easy maintenance.
4. Durable Material, capable of bearing most crashes without any damage.
5. Fully assembled and tested in the factory.
6. New high-tech 4-channel 2.4G rc system.
7. Digital sub-micro servos offer precise and powerful control.

]]>

Honey Bee 4CH RC helicopter

Thu, 28 Jan 2010 14:17:30 +0000

]]>

The Honey Bee radio controlled helicopter is the best 4 channel beginner helicopter on the market. We tried all the different models available before deciding which helicopters to stock and found the Honey Bee was by far the most stable and best quality. This is not the cheaper Honey Bee "T" but the upgraded Honey Bee with a bigger 7.4V Li-Po battery pack and more powerful 370 motor. Everything you need is included.

The Honey Bee comes with a 4 channel radio control. It is UK spec 35mhz with mode 2 controls (left hand throttle).

Specs:
(1)Main rotor diameter: 520mm
(2)Weight: 290g
(3)Length: 510mm
(4)Main blade material: plastic
(5)Power system: 370 motor
(6)KIT or RTF: RTF
(7)Control mode: normal
(8)Transmitter: 4CH system
(9)Mix controller: "4 IN 1" controller(W/gyro,mixer,ESC, receiver)
(10)Servo: 8g,1.3kg/CM,0.13s/60
(11)Battery: 7.4V-800mAh Li-Po with UK charger
(12)Flying radius: ~400m
(13)Flight time: ~15 minutes

Features:
Excellent design for your indoor flight
Pre-position servo mounts for easy setup
Carbon fibre and flybar and boom for superior strength and durability
Ready for flight out of the box
New version with Li-Po battery

]]>

Esky 2.4G Chinook 4Ch Radio Controlled Helicopter

Thu, 28 Jan 2010 14:12:08 +0000

]]>

The all new Chinook helicopter from Esky looks fantastic and is great fun to fly. This is a proper 4ch helicopter giving it full 3d control including banking left and right which is something that the other 3ch ones on the market can not do. It also has a high capacity 7.4v li-po battery giving loads of power and proper Esky radio equipment giving it a much greater range. The Chinook has four sets of blades powered by four separate motors and along with the built in gyro and digital servos make this helicopter fun and responsive to fly.

The Chinook is available in two different styles. A coast guard finish as per the picture at the top or a military camouflage finish as can be seen in the picture below.

The Chinook comes totally pre built with everything needed to get flying included in the box. The helicopter radio equipment is the latest high quality 2.4Ghz version from Esky which makes it very reliable and also means that many helicopters can be used at the same time without interfering with each other. Included in the kit is also some spare blades in case you damage the original ones.

Specifications:
Length: 251mm
Width: 56mm
Height: 153mm
Rotor diameter: 210mm
Weight: 145g
Motors: 4 x N30
Transmitter/Receiver: 2.4GHz 4CH
Battery: 7.4V 450mAh Li-polymer
3in1Controller (gyro, mixer, ESC)
Servos: Digital 4g, 0.5kg/cm, 0.12s/60°

Features:
1. Completely assembled and tested at the factory.
2. Twin coaxial rotor systems.
3. Four high performance micro motors provide the ultimate in thrilling flight.
4. Uses the latest 2.4GHz radio control system technology.
5. Two high performance micro digital servos.
6. 3 in 1 control unit provides amazing stability that newcomers will find reassuring.

]]>

Esky Dauphin 4ch Rc Helicopter - 2.4G Version

Thu, 28 Jan 2010 14:05:01 +0000

]]>

The Co-Dauphin boasts a highly realistic appearance and excellent craftsmanship. It makes flying more interesting with the ducted tail rotor, colored lights and retractable tricycle wheel. The helicopter was designed by ESky as a 4CH helicopter with a co-axial, double rotor blade system. This makes it very easy to fly so can been flown by anyone with minimum practice and are therefore a great way to get into the hobby. You can have all the fun and thrills of flying a proper rc helicopter but without the hours of practice. Not to be confused with the toy twin blade helis, this is a proper model featuring a proper 4 channel controller, long lasting lithium battery and gyro.

The Co-Dauphin is Ready to Fly out of the box. The electronic system has been completely adjusted by the Esky engineers before leaving the factory. All you need to do is charge the battery and then you will be flying in no time. The package also includes transmitter, UK charger, spare blades, rechargeable battery, transmitter batteries, Esky simulator cable and instructional video CD.

The new 2.4GHz remote control system adopts Advanced Spread Spectrum technology and digital FSK (Frequency Shift Key) coding technology. The digital servos provide rapid response, precise reaction and nimble movement. With this system, several flyers can operate simultaneously within the same area, ensuring a safe and fun flying experience.

Specifications:
Length: 400mm
Height: 180mm
Width: 72mm
Main rotor diameter: 340mm
Weight: 240g
Battery: 7.4V 800mAh Li-po with UK Charger
Motor: 2 x 180
Transmitter: 2.4GHz 4CH
Receiver: 2.4GHz 4CH
3in1 controller: Gyro, mixer, ESC
Servos: Digital 7.5g, 1.0kg/cm, 0.1s/60°

Features:
1. Great realistic design
2 . Flight simulator included
3. Simple mechanical structure design, easy maintenance.
4. Twin blades makes flying easy.
5. Fully assembled and tested in the factory.
6. New high-tech 4-channel 2.4G rc system.
7. Digital sub-micro servos offer precise and powerful control.
8. Flashing tail light.

]]>

Esky Co-Comanche 4ch RC Helicopters

Thu, 28 Jan 2010 13:55:50 +0000

]]>

The Co-Comanche is one of the coolest looking RC helicopters on the market. Unlike the usual boring shells that come with most helis, this one comes with a realistic looking camouflaged army style. The model is based on the RAH-66 Co-Comanche which is a new helicopter being used for reconnaissance missions and assaults on land forces.

The helicopter was designed by ESky as a 4CH helicopter with a co-axial, double rotor blade system. This makes it very easy to fly so can been flown by anyone with minimum practice and are therefore a great way to get into the hobby. You can have all the fun and thrills of flying a proper rc helicopter but without the hours of practice. There are many twin blade RC helicopters on the market now but the Comanche is in a league of it's own with much better performance and agility. Not to be confused with the toy twin blade helis, this is a proper model featuring a proper 4 channel controller, long lasting lithium battery and gyro.

The Comanche comes with everything included in the box including the fully built heli, instructions, 4 ch controller, lithium battery, lithium charger, UK 240V ac/dc adaptor, 12V car battery adaptor, AA batteries for the controller, a flight simulator software programme and even a couple of spare blades in case you break one. It comes in a cool display box which makes it a great gift for any teen or big kid!

The Comanche comes with a high quality 4ch controller. You can choose between the Mhz version with changeable frequency crystals or the Ghz version which does not require different crystals to be used with other models in the same area. Both are UK mode 2 which means that the throttel control is on the left hand side. This is a proper radio set that you should not confuse with the ones that come with the toy RC helicopters which have a very short range. These ones have a range of hundreds of meters!

This helicopter was designed with a divided canopy and fuselage connected by a carbon fibre rod which is practical and looks great. There are three sliding wheels in the landing strut, which can slide automatically while taking off and landing. The ornamental tail houses a ducted rotor blade that actually rotates automatically when flying the helicopter! ESKY's original transmitter to computer cable is included in the pack. Installing the flight simulator software from the enclosed disc on your computer and connecting the simulator port in the transmitter to the computer will allow you to practice your flying on your computer before going for your real flight!

Specs:
(1).Main rotor diameter:340mm
(2).Weight:242g
(3).Length:435mm,width:95mm,height:185mm
(4).Power system:180 motor*2
(5).RTF
(6).Transmitter: 4CH (including training switch and simulator port. Choice of Mhz or 2.4 Ghz)
(7).4 in 1 mix controller (W/gyro,mixer,ESC,receiver)
(8).Servo:(8g,1.3kg.CM,0.12s/60¡)
(9).Battery:7.4V 800mAh Li-polymer battery

Features:
(1).Novel and distinct sculpt with high emulation art
(2).Designed for beginner and is suitable for indoor flight
(3).Lifter pulley and culvert tail rotor design ensure a more enjoyable flight
(4).Airline operation with graceful movements and sensitive reaction
(5).RTF after unwrapping the packing and fixing the battery and dispense with debugging

]]>

Esky Lama V3 RC Helicopter

Wed, 27 Jan 2010 15:38:06 +0000

]]>

This is the famous Esky Lama co-axial helicopter. It is the best quality and best flying twin blade helicopter on the market. Not to be confused with the toy twin blade RC helicopters, this is a proper model featuring a proper 4 channel controller, long lasting lithium battery and gyro.

Twin blade RC helicopters can been flown by anyone with minimum practice and are a great way to get into the hobby. You can have all the fun and thrills of flying a proper rc helicopter but without the hours of practice. There are many twin blade RC helicopters on the market now but the Lama V3 is in a league of it's own with much better performance and agility.

The Lama comes with everything included in the box including the fully built heli, instructions, 4 ch controller, lithium battery, lithium charger, UK 240V ac/dc adaptor, 12V car battery adaptor, AA batteries for the controller and even a couple of spare blades in case you break one. It comes in a cool display box which makes it a great gift for any teen or big kid!

The Lama comes with a high quality 35mhz 4ch controller with changeable frequency crystals. It is a UK mode 2 which means that the throttel control is on the left hand side.

Specs:
Main rotor diameter: 340mm (13.4 inch)
Overall length: 360 mm (14.2 inch)
All-up weight: 215g (Battery included)
Driven system: 2* 180 carbon motors
Servo: 2X 8g Servos and inside Gyro
Battery: 7.4V 800mAh Li-polymer
Control system: 4CH Multifunctional FM Transmitter and 3-in-1 Receiver
Radio Control Range: 3300 feet (1000m)
Frequency: 35Mhz with changeable crystals
Required to fly: Nothing!

Features:
Improved V3 version
4 Ch transmitter
Super Stable X-Rotation System
Coaxial counter-rotating blades
Precise controlling and easy hovering
Weight saving 3-in-1 Mixer/Gyro/Receiver
Reliable high quality mixer with built-in gyro
Suitable for Indoor/Backyard/Park flying
Powerful 800mAh Li-polymer battery.
Proportional Motor Speed Control
Top quality stronger blades
Separate servos from mixer
Trimming of servos can be done both on helicopter or on transmitter.
Approximately 15 minutes flight time
Best choice for Beginner and Advanced
Full parts backup
Complete Kit, Ready to Fly

]]>

E-Sky Kob 4Ch Co-axial RC Helicopter

Wed, 27 Jan 2010 15:30:23 +0000

]]>

The Kob is designed to be the ultimate entry level helicopter into the world of professional rc helicopter flight. Every part of the helicopter has been carefully thought out by industry leaders E-Sky to make both flying and maintenance as easy as possible. The focus has been on simplifying the build as much as possible by making all parts accessible without having to strip the whole model. The co-axial blade system along with the high spec electronics, gyro and digital servos makes flying much easier and stable for beginners. Should you have a crash though and break something this simplified design will mean repair times will be much shorter allowing you spend more time flying and less time fixing. Everything you need to start flying is in the box including all batteries chargers and cables.

Although this helicopter has been designed for easy flight it is still a high spec full function model. The 4 in 1 controller has a built in gyro, receiver, ESC and mixer that all work to give more control and make flight more stable. The battery is a 800mAh li-polymer which gives more power and flight time than standard batteries. Even digital servos have been used which give very precise control and allows you to fly the helicopter exactly where you want it to go.

The Kob comes with a high spec E-Sky 4ch transmitter. You can choose between the Mhz version with changeable frequency crystals or the Ghz version which does not require different crystals to be used with other models in the same area. This handset has a massive 1000m+ range and allows precise 3D control of the helicopter. It also features a training switch that means it can be connected to another E-Sky handset when learning so that at any time control can be passed to the other handset that can be in the hands of an experienced flyer. The sim port means it can be connected to a computer with the included cable and you can get some flight time on the simulator before flying the real thing.

Specifications:
Main Rotor: 340mm
Weight: 226g
Length: 415mm
Width: 77mm
Height: 174mm
Motors: 2 x 180
Transmitter: 4Ch (includes training switch and simulator port. Choice of 2.4G or Mhz)
Mix controller: 4 in 1 (with gyro, mixer, ESC & receiver)
Servos: 7.5g digital
Battery: 7.4V 800mAh Li-polymer

Features:
1. Co-axial, counter-rotating double blades system.
2. Easy to fly with simple operation, designed for beginners.
3. Ready to fly out of box
4. Digital servo with precise movements and sensitive reaction.
5. Efficient, precise control.
6. Simple structure of landing skid ensures convenient adjustment and easy maintenance.
7. Complete package with everything included.

]]>

Apache 4ch RC Helicopter

Wed, 27 Jan 2010 15:20:06 +0000

]]>

This RC helicopter looks amazing and is very easy to fly. There are now a lot of twin blade helicopters on the market but none look as good as the Apache. Twin blade helicopters can been flown by anyone with minimum practice and are a great way to get into the hobby. You can have all the fun and thrills of flying a proper rc helicopter but without the hours of practice.

Not to be confused with the toy helicopters though, this is a proper model with full 3D control. There is a similar two channel version on the market with very limited control but this is the better four channel one that allows you to go up and down; rotate right and left; bank left and right, and move forwards and backwards.

The Apache RC helicopter comes complete with everything you need. The only thing required to use is 8 normal AA batteries for the controller.

SPECIFICATIONS:
Rotor Diameter: 260MM
Length : 300MM
Weight: 80g
Flight time: 8 - 12 minutes
Transmitter: FM 4 channel
Motor: 2 x strong magentic brushed
Battery: Lithium Polymer 7.4V 350mAH

CONTENTS:
Factory Assembled RC Helicopter
4Ch 35mhz Transmitter
UK AC Li-Po balanced charger
Li-Po 7.4V 350mAH
Instruction Manual

]]>

Walkera 5G6 MicroX - 4 channel rc helicopter

Wed, 27 Jan 2010 15:14:17 +0000

]]>

The most innovative and fun RC helicopter of the year, the Walkera 5G6 is a must have gadget for any tech lover. These sell for £99 on the high street and on other sites. This is the Micro-X version where we have added our own finish to them with a custom shell and colour.

Don't confuse these with the cheap 2ch/3ch RC helicopters that you may have seen on the market, these are an engineering masterpiece with a full 4 channel long range control system and built in gyro. With the 2ch helicopters you can only go up and down and rotate and they have a very small range. With these you have 3D control that allows you to go up and down; rotate right and left; bank left and right, and move forwards and backwards plus the range is a couple of hundred meters like on full scale models. For their cute palm size this is an amazing achievement. Power is provided by a rechargeable high capacity lithium polymer battery pack that gives a longer 7-10 minutes flight time. Included is a lithium battery charger with a UK plug.

The helicopter is excellent quality and comes in a neat good looking gift box. The heli uses counter rotating blades that makes flying them very easy. The 5G6 is great fun and makes a perfect gift for anyone or yourself!

Please note the set includes a rechargeable battery pack and charger and is therefore recommended for ages 14+.

SPECIFICATIONS:
1) Main Rotor Diameter (Upper): 175 mm
2) Main Rotor Diameter (Lower): 175 mm
3) Overall Length: 175 mm
4) Drive System: 2×1215 strong motors
5) Battery: 3.7V 400mAh Li-PO battery
6) All-up Weight: 57g (Battery included)
7) Transmitter: 4 Ch
8) Gyro: Built-in
9) Receiver: RX-412
10) Servo weight: 3.5g
11) Servo speed: 0.11sec/60°(4.8V)

FEATURES:
1) Coaxial structure and palm-sized dimensions are used to make this the best model for indoor entertainment.
2) 2×1215 strong-magnetic motors are powerful and make flight stable.
3) Highly efficient special servo (3g) with super response times
4) The receiver is equipped with a built-in gyro with adjustable sensitivity.
5) High capacity 3.7V 400mAh Li-po battery pack. A full charged cycle will give 7-10 minutes flight time.
6) The worlds smallest 4ch RC helicopter!

]]>

HSP 1/8th Radio Controlled Off Road Crawler

Wed, 27 Jan 2010 15:00:44 +0000

]]>

The new HSP 1/8th scale radio controlled crawler is equipped with twin motors and a lot of metal parts to ensure solid construction and performance. A high precision ESC is also equipped on the Car. The 1/8th scale rock crawler allows you to climb over the most challenging rugged terrain.

Specs:
Height: 225mm
Length: 645mm
Width: 375mm
Gear Ratio: 1:48
Motors: 2 x 540
Weight: 5300g
Wheelbase: 460mm
Radio: 2ch Stick type 27mhz
Wheel Diameter: 182mm
Wheel Width: 82mm
Battery: 7.2v 2000 MaH

Features:
1. Independent front/rear gear box
2. Twin motor driven system
3. Aluminium solid side guards
4. Aluminium oil filled shock absorbers
5. Equipped with lots of metal parts
6. 1/8 the scale body design
7. High quality off-road climbing tyres
8. The perfect design enables the Crawler to climb over the most challenging rugged terrain
9. Battery is well fixed with plate set, no failing off but easy to take out
10. Chrome plated Wheel Secure Cover is fixed by 18 screws ensuring the Tyre and Wheel Rim do not separate.
11. Suitable for all terrains indoor & outdoor

]]>

1/10th Radio Controlled Crawler

Wed, 27 Jan 2010 14:55:55 +0000

]]>

If speed is the key to racing, finesse is the key to rock crawling. RC rock crawling is a test of machine, concentration, driving ability and sheer will. RC rock crawlers carefully negotiate difficult rock formations and surmount obstacles that ordinary vehicles couldn't even begin to climb. At times, it is a slow, deliberate navigation and at times its an almost violent display of brute force. In the last few years, more and more specialised, purpose-built RC crawlers have been built that perform better, and better emulate the full-size rock crawlers that are growing extremely fast in popularity as well.

Acme Tech knew they would need to do something special to stand out in the crawler market and they have succeeded in their mission by a long way. The Acme Tech RC Crawler is an aluminium masterpiece that looks like a piece of art. Almost all the model is made from beautifully machined aluminium with hardened steel used where the crawler needs it most. The model not only looks amazing but is also a great performer. For crawling a vehicle needs power and manoeuvrability. This crawler features a twin 540 motor setup with a gear ratio of 1:147 for powering up rocks or whatever else you put in front of it! It also features amazing flexibility and a high torque steering servo. When you are ready to upgrade your model you can add rear wheel steering or swap the wheels for the massive oversized ones. The crawler comes fully built with standard fitting 7.2v battery pack and UK charger included. All that is required to use is 8 normal AA batteries for the radio handset.

The RC crawler comes with these fantastic machined aluminium bead lock wheels that are extremely strong and make it easy to change tyres for different course conditions. The tyres have a tread pattern that is good for most rock crawling courses. The suspension link rods allow the chassis to articulate almost 90 degrees and the tie-rods are adjustable so you can make toe-angle adjustments to the front and rear wheels.

The gearbox is also made from high strength machined aluminium with a window so you can see the gears inside. The crawler features solid drive shafts and steel gears that are perfect for rock crawling. The axle carriers are machined from aluminium for strength and feature and feature ball bearings to support the drive shafts and axles. The shocks are all oil filled and use a spring that is well suited for most rock climbing conditions. The shocks feature threaded shock bodies that allow the shocks to be easily tuned for different conditions. The shocks come standard with #200 (20 weight) oil and blue springs.

Specifications:
1) Wheelbase: 320mm
2) Length: 450mm
3) Width: 310mm
4) Height: 235mm
5) Wheel dia: 28mm x 60mm
6) Ground clearance: 120mm
7) Body: 368L x 135W x 120H mm
8) Motor: 2 x 540
9) Servo torque: 5kg/cm
10) Gear ratio: 1:147
11) Total weight: 3.5kg
12) Required to use: 8 x AA batteries
13) Battery pack: 7.2v 1800MaH w/ charger
14) Radio: 27 mhz

Features:
1) Fully assembled RC Crawler with radio
2) Solid aluminium construction
3) Oil filled shocks
4) Steel linkage rods
5) Steel drive shafts
6) Aluminium gearbox
7) Steel gears
8) High torque front steering servo
9) Optional 4 wheel steering upgrade
10) Twin high torque motors
11) 2 way ESC for proportional control
12) Solid aluminium wheels

]]>